Stand-Alone System Connections:
The diagram below shows a basic IR distribution system using the ATON AIB4
Amplified IR Connection Block, AIR3 IR Receiver, and AIE1 and AIE2 IR Emitters to
control various source equipment.
Mounting the AIR3
Limited Warranty
AIR3
The AIR3’s low-profile design allows for flush-mounting in walls, cabinets, etc.
ATON* warrants to the purchaser/end user (“you”) that the AIR3 is to be free from defects in materials and
workmanship for a period of five (5) years from date of purchase (the “Warranty Period”). This warranty is
transferable to subsequent owners of the product as long as the original proof of purchase is retained. If
you discover a defect in material or workmanship within the Warranty Period, you can obtain warranty ser-
determines that the product is in fact defective, ATON shall, at its option, repair or replace the product free
of charge to you.
The following steps must be completed prior to making connections.
Plasma Friendly
To correctly mount the AIR3:
Flush-Mount
1. Drill a 1/2 inch hole in the mounting surface.
2. Insert the AIR3 into the hole. Install the mounting bezel from the
front.
Digital Music Server
IR Receiver w/Plug
This warranty shall not apply to equipment (a) not manufactured by ATON, (b) to equipment which was
improperly installed, (c) which was repaired or altered by persons other than ATON or its authorized repre-
sentatives or subject to unauthorized tampering, alteration or modification, (d) damaged due to misuse,
negligence, accident, acts of God (including, but not limited to, excess moisture, insects, lightning, flood,
electrical surge, tornado, earthquake, or other catastrophic events beyond ATON’s control), or (e) subject to
improper operation, maintenance or storage or unreasonable use. The foregoing warranties do not cover
reimbursement for labor, transportation, removal, installation or other expenses which may be incurred in
connection with repair or replacement. The foregoing remedies shall be your exclusive remedies for any
breach of warranty.
Remote Control
Introduction
AIR3
Plasma Friendly
Flush-Mount
IR Receiver
3. Install the jam nut from the back of the unit. Do not overtighten!
AIE2 Talk-Back Emitter
Satellite
The ATON AIR3 is designed to mount flush in a cabinet or wall and is an ideal
choice whenever an inconspicuous IR receiver is required. This receiver uses
advanced IR filtering technology which allows it to work even in areas that receive
normally harmful interference (near plasma TVs, compact flourescent lights, etc.).
The AIR3 features a 3.5mm plug for easy connection to IR distribution blocks, multi-
room controllers, etc.
Mounting
Jam Nut
Further, the foregoing warranty does not extend to equipment sold, but not manufactured by, ATON (“Third
Party Products”). With respect to any Third Party Products, the warranty for such product shall be as pro-
vided by the manufacturer of such product, who will also be responsible for warranty service, and ATON will
pass through to you any transferable warranty actually extended to ATON by the manufacturer.
THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESSED AND IMPLIED
WARRANTIES. ATON EXPRESSLY DISCLAIMS ALL SUCH OTHER WARRANTIES, INCLUDING BUT NOT LIMITED
TO IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-
INFRINGEMENT. Notwithstanding the above, where applicable, if you qualify as a “consumer” under the
Magnuson-Moss Warranty Act, then you may be entitled to any implied warranties allowed by law for the
Warranty Period. Some states do not allow limitations on how long an implied Limited Warranty lasts, so the
above limitation may not apply to you.
Bezel
AIE2 Talk-Back Emitter
DVD
Features
PS2
• 3.5mm Plug Accommodates IR, +12VDC, & GND
• ‘Plasma-Friendly’ Technology Helps Block Plasma TV Interference
• Ambient Light Filtration
Power
Supply
1/2"
AIE1 IR Emitter
AIB4
To 120V AC
(unswitched)
Amplified IR
Connection Block
• Low-Profile Flush-Mount Design
ATTENTION: TO OUR VALUED CONSUMERS
Figure 2
Valid proof of purchase is required for all warranty services. Warranty service requests made without proof
of date of purchase will be denied. Please keep the original sales receipt for your records and send a copy to
request warranty service.
IR OUT
GND
+12VDC
Jam Nut
IR Lens
This warranty gives you specific legal rights, and you may also have other rights which vary from state to
state.
* ATON is a division of ELAN Home Systems, LLC.
1. Mount the AIR3 IR Receiver in a wall, cabinet, etc.
Figure 3
2. Plug the AIR3 and IR emitters into the ATON AIB4 as shown.
3. Set the DIP switches on the AIB4 to LP ON and NET ON or OFF.
4. Plug in the power supply.
5. IR signals sent to the AIR3 will pass through the AIB4 and control
the equipment.
Advanced IR Filtering Technology
Striped Side
3.5mm Plug
The AIR3 features Advanced IR Filtering Technology that reduces IRI, CFL, EMI,
and ESI noise sources in addition to blocking plasma TV emissions. This means
that the AIR3 can be used in areas that receive substantial ambient noise such as
near plasma TVs or compact flourescent lights.
AIR3
8' Lead
Mounting Bezel
Figure 1
Specifications:
• Requires 12VDC power supply, IR distribution block (or equivalent),
and IR emitters for operation.
• Mounting: Install in walls, cabinets, etc.
• Power: +12VDC @ 10mA
• Carrier Frequency Acceptance Range: 20kHz to 100kHz
• Control Range: Up to 30 feet on-axis, 25 feet off-axis (+/-30degrees)
depending on remote strength and ambient noise conditions
• Room-to-Room Wire Recommendations: Cat-5
or
• Maximum recommended cable length: 1200 feet using Cat-5
• Dimensions: 1 7/8" (47mm) L x 15/32" (12mm) W (w/out bezel)
©2007 • All rights reserved.
P/N 9900896 REV:B
1
2
3
4
|