Back light
and Setting
TIME TIMER
0
Start,
Stop, &
Reset
Timer
™
Watch Plus
30
Change
Modes
30M
WATER RESIST
“the difference is the disk”
Introduction
Using the Timer
Congratulations on your purchase of theTimeTimer
Watch Plus™! No other tool communicates the concept
of elapsed time as well as theTimeTimer.TimeTimer
reinforces the sense of elapsed time with a graphic
depiction of the time remaining.
Press the MODE button (lower
left) until you see theTime
Timer’s red dial.
Press
Once to
Start and
Twice
quickly
to Stop.
TIME TIMER
The timer can be set any-
where from one minute up
to 12 hours.There is both an
audible alarm and also a pre-
alarm to let you know when
time is running out or has
expired.
0
For years,TimeTimer desktop timers have been used
effectively to help teachers, business people, and students
of all ability levels manage their time more effectively.
With the newTimeTimer Watch Plus, you can have more
flexibility and portability in time management than ever
before.
Press
and
Hold
to
30
The watch comes from the
factory with the timer set to
one hour (indicated by 1:00
in the middle of display), and
the audible alarms set to OFF.
Reset.
30M
WATER RESIST
Understanding the Watch
TheTimeTimer Watch Plus has two modes of operation
–Timer andTime of Day.To change between modes, press
the MODE button (lower left).
To change the settings, see instructions below.
•
•
To Start the timer, press theTIMER button (upper right).
To Stop the timer, press theTIMER buttonTWICE, in rapid
succession (press the button twice within ½ second).
To Reset the timer, press and hold theTIMER button for at
least 2 seconds.
TheTimer mode provides a graphical count down timer,
using the patentedTimeTimer technology. A red disk
surrounds digits – both represent the time remaining.
The disk and digital display both diminish as time elapses
until no red is visible on the timer face, and the digits read
“0:00”.Time elapses in a clockwise direction. When active,
the Pre-Alarm and Alarm sound to let you know that time
is running out or has expired.
•
If turned ON, the Alarm will sound when time expires.The alarm
sounds for 5 seconds, or until cancelled by pressing any button.
If turned ON, the Pre-Alarm will sound according to the schedule
shown below (note that Pre-Alarm can be used only if Alarm is
also being used).
TIME TIMER
TIME TIMER
TIME TIMER
0
0
0
Table of Pre-Alarm vs Time Setting
Time Set
< 3 min
Pre-Alarm at last:
10 sec
30
30
30
30M
WATER RESIST
30M
WATER RESIST
30M
WATER RESIST
3 - 10 min
10 - 30 min
> 30 min
30 sec
1 min
5 min
59 minutes
remaining
45 minutes
remaining
Time’s up
Suggested Applications
In the workplace,TimeTimers can be used to:
Time of Day uses a traditional “analog” watch face to
show the current time, along with a digital display of time.
The watch also includes aTime of Day Alarm.
•
•
•
•
•
•
•
Time seminars, meetings, panel discussions and presentations
Quantify time left before appointments and deadlines
Monitor break time
Manage progress toward goals and agenda items
Oversee skills tests
Regulate study time, computer time and play time
Measure “time out”
#998-310A
The watch also comes with a convenient back light, to
help you see the display in low light conditions. Press the
LIGHT button (upper left) to turn on the back light.
From Hour setting mode, press S2 once to enter Minute
setting. Minute hand and digits will be flashing. Set
current Minutes using the S3 buttons.
Manufactured for
TimeTimer, Inc.
7707 Camargo Road
Cincinnati, OH 45243
From Minute set, press S2 once to enter Second setting.
The second hand will be flashing. Press either S3 button
to reset seconds to zero.
(513) 561-4199
Fax (513) 561-4699
From Seconds set, press S2 once to enter Alarm setting.
The letters “AL” will be flashing, and you will also notice
that the watch hands have disappeared.You can turn the
Time of Day alarm On or Off by pressing either S3 button.
When On, you will see a small Alarm Bell \ next to the
AL indicator.
1-877-771-TIME
(1-877-771-8463)
U. S. PATENT NO. D369, 619 & 5,662,479
From Alarm On/Off, press S2 once to enter Alarm Hours
setting.The “AL” indicator and the Hours digits will be
flashing, and the clock hands will not be visible. Use
the S3 buttons to set the desired Alarm Hour setting.
REGISTER NOW.
Email __________________________
User ___________________________
_______________________________
_______________________________
Please return your AX810TT
registration to the Repair Center
address in the warranty, and we
will let you know about future
products.
From Alarm Hours, press S2 once to enter Alarm Minutes
setting.The “AL” indicator and the Minutes digits will be
flashing, and the clock hands will not be visible. Use the
S3 buttons to set the desired Alarm Minutes setting.
5 YEAR NO-PROOF-OF-PURCHASE LIMITED WARRANTY
Free service for first year (see back of watch for date).
$15 fee applies thereafter. Return unit with daytime phone number to:
AST Repair Center, 3090 Independence Drive, Suite 148
Livermore, CA 94551 USA 800-935-1996 • 925-290-1900
From any of the setting fields, press S4 once (upper left)
to exit setting mode. Leaving the watch unattended for
30 seconds in set mode causes it to save any changes
and then exit set mode.
Changing the Battery
When the display grows dim or goes out entirely, it is
time for a new battery. Using a small Phillip’s head
jeweler’s screwdriver, remove the four screws holding
back of watch onto case. Gently slide the old battery
from its slot, and replace with new CR2025 Lithium
battery. Make sure that the positive (“+”) terminal side
is facing up.
Power Reset
You can reset the watch to original factory settings by
pressing S3+ and S3– (the two lower buttons) together,
and holding for at least five seconds.
Developed by Time Timer LLC, in cooperation with Abilitations.
|