Analog LCD Monitor
AL1702 User’s Manual
AL1702 E-1
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide resonable
protection against radio frequency interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy. If not installed and used in
accordance with the instructions, it may cause interference to radio communications.
However, there is no guarantee that intereference will not occur in a particular installation.
If this equipment does cause interference to radio or television reception (this can be
determined by turning this equipment off and on), the user is encouraged to try to correct
the interference by one or more of the following measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between this equipment and the receiver.
Connect this equipment to an outlet on a circuit different from which the
receiver is connected to.
•
Consult the dealer or an experienced radio/TV technician for help.
Caution:
To comply with the limits for an FCC Class B computing device, always use the shielded
signal cable supplied with this unit.
Caution to the user:
The Federal Communications Commission warns the user that changes or modifications to
the unit not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
Notice of Compliance Canadian
Interference-causing Equipment Regulations
DOC Compliance Notice:
This digital apparatus does not exceed the Class B limits for radio noise emissions from
digital apparatus set out in the Radio Interference Regulations of the Canadian Department
of Communications.
DOC Avis de Conformation
Le présent appareil numérique n’emet pas de bruits radioélectriques dépassant les limites
applicable aux appareils numériques de la class B prescrites dan le Réglement sur le brouillage
radioélectriques édicté par le ministére des Communications du Canada.
E-2 User’s Guide
INTRODUCTION
Congratulations for purchasing modelAL1702, a high performance 17-inch color TFT LCD
monitor. TheAL1702 monitor provides flicker-free and color images at optional resolutions.
Through this user guide, we will introduce you step-by-step all the features, functions and
technical specifications of the LCD monitor. Surely you will have a refreshing experience
working with the monitor.
FEATURES
The AL1702 is a 17-inch TFT LCD monitor that is intelligent, microprocessor-based and
ergonomically designed display, compatible with most analog RGB (Red, Green, Blue)
display standards, including PS/V, PS/2, optional for Apple Macintosh Centris, Quadra,
and Macintosh II family signals. The LCD monitor is capable of displaying crisp and
vibrant color graphics with VGA, SVGA, XGA, SXGA (non-interlaced), and most Macintosh
compatible color video cards.
•
The monitor is able to properly function even in case of upgrade video cards or
software because of the wide auto-scanning compatibility range without requiring to
buy a new monitor.
•
The internal microprocessor digitally controls auto-scanning. For horizontal scan
frequencies between 30 KHz and 81 KHz, and vertical scan frequencies between 55 Hz
and 76 Hz. In each frequency mode, the microprocessor-based circuitry allows the
monitor to function at the precision-of a fixed frequency.
•
•
•
•
The resident memory allows for storing factory default settings and also additional
user adjustment parameters.
The maximum resolution achievable is SXGA (1280 x 1024), best suited for Windows
applications
The compact and sleek cabinet design saves lot of your desk space and makes your
desk look neat and tidy.
The monitor is also compliant with the most stringent environmental scheme of TCO
99. In this scheme, no environmental harmful substances are used during the entire
manufacturing process.
AL1702 E-3
UNPACKING
Please check the following items are present when you unpack the box, and save the
packing materials in case you will need to ship or transport the monitor in future.
•
LCD Monitor
Speakers
•
AC Power Cord
•
Audio Cable
•
User Manual
E-4 User’s Guide
Attaching / Removing the Base
Install:
Remove:
Align the four hooks on the bottom of
the monitor with the corresponding
slots on the bottom of the base.
Depress the hook as indicated first
before removing the base and follow the
arrow direction to remove it.
SCREEN POSITION ADJUSTMENT
In oder to optimize the best viewing position, you can adjust the tilt of the monitor by
using both of your hands to hold the edges of the monitor as shown in the figure below.
The monitor can be adjusted to 30 degrees up or 5 degrees down as indicated by arrow
below.
AL1702 E-5
CONNECTING THE POWER CORD
•
Check first to make sure that the power cord you use is the correct type required for
your area.
•
This monitor has a universal power supply that allows operation in either 100/120V
AC or 220/240 V AC voltage area. No user-adjustment is required.
•
•
Plug one end of the power cord to the AC Inlet, plug another end to a proper AC outlet.
For unit using at 120 V AC:
Use a UL Listed Cord Set, Type SVT wire and plug rated 10 A/125 V.
•
For unit using at 220/240 V AC (outside of U.S.):
Use a Cord Set consisting of H05VV-F cord and plug rated 10 A, 250 V. The cord set
should have the appropriate safety approvals for the country in which the equipment
will be installed.
SAFETY PRECAUTION
•
Avoid placing the monitor, or any other heavy object, on the power cord to avoid
damage to the cable.
•
•
Do not expose the monitor to rain, excessive moisture, or dust.
Do not cover the ventilation slots or openings of the monitor. Always put the monitor
in a place where there is adequate ventilation.
•
Avoid placing the monitor against a bright background or where sunlight or other
light sources may reflect on the face of the monitor. Place the monitor just below
eye level.
•
•
Handle with care when transporting the monitor.
Refrain from giving shock or scratch to the screen, as screen is fragile.
CLEANING YOUR MONITOR
Please carefully follow the below guidelines when cleaning the monitor.
•
•
•
Always unplug the monitor before cleaning.
Use a soft cloth to wipe the screen and cabinet front and sides.
Apply a small quantity of alcohol to a soft cloth to clean the monitor screen, if requires
more than dusting.
E-6 User’s Guide
PRESET MODES
To reduce the need for adjustment for different modes, the monitor has default setting
modes that are most commonly used as given in the table below. For optimum adjustment,
the user is suggested to perform the Auto Setup under Windows “Full Screen” pattern. If
the mode in use does not match one of the defaults, the user can store their preferred
modes in the user modes. The monitor is capable of storing up to 9 user modes. The only
condition to store as a user mode is the new display information must have 1 KHz difference
for horizontal frequency or 1 Hz for vertical frequency or the sync signal polarities are
different from the default modes.
Polarity
H. Freq.
(KHz)
Band Width
(MHz)
Mode
Resolution
H
-
V
+
-
1
2
VGA
720 x 400
640 x 480
640 x 480
640 x 480
640 x 480
800 x 600
800 x 600
800 x 600
800 x 600
832 x 624
1024 x 768
1024 x 768
1024 x 768
70 Hz
60 Hz
66 Hz
72 Hz
75 Hz
56 Hz
60 Hz
75 Hz
72 Hz
75 Hz
60 Hz
70 Hz
75 Hz
31.47
31.47
35.00
37.86
37.50
35.16
37.88
46.88
48.08
49.72
48.36
56.48
60.02
64
28.322
25.175
32.24
31.5
31.5
36
VGA
-
3
MAC
VESA
VESA
VESA
VESA
VESA
VESA
MAC
VESA
VESA
VESA
VESA
VESA
VESA
VESA
-
-
4
-
-
5
-
-
6
+
+
+
+
-
+
+
+
+
-
7
40
8
49.5
50
9
10
11
12
13
14
15
16
17
57.283
65
-
-
75
-
-
78.75
108
+
+
+
+
+
+
+
+
+
+
1280 x 1024 60 Hz
1280 x 1024 75 Hz
80
135
1152 x 864
1280 x 960
75 Hz
60 Hz
67.5
108
60
108
AL1702 E-7
POWER SAVING
The monitor will be driven into “Power Saving” mode by the control signal from the
display controller, as indicated by the amber-color power LED.
Power
Consumption
State
LED Light
Green
ON
Normal
Active
OFF
< 3 W
Amber
The power saving states will be kept until a control signal has been detected or the
keyboard or mouse is activated. The recovery time from Active OFF state back to ON state
is around 3 seconds.
DDC
To make your installation easier, the monitor is able to Plug and Play with your system if
your system also supports DDC protocol. The DDC (Display Data Channel) is a
communication protocol through which the monitor automatically informs the host system
about its capabilities, for example, supported resolutions and corresponding timing. The
monitor supports DDC2B standard.
E-8 User’s Guide
INSTALLATION
To install the monitor to your host system, please follow the steps as given below:
Steps
1. Connect Video Cable
a. Make sure both the monitor and computer are powered-OFF.
b. Connect the video cable to the computer.
2. Connect power cord
Connect the power cord to the monitor, then to a properly grounded AC outlet.
3. Connect the Audio Cable.
4. Power-ON Monitor and Computer
Power-ON the monitor first, then power-ON the computer.
This sequence is very important.
5. If the monitor still does not function properly, please refer to the troubleshooting
section to diagnose the problem.
Please don’t open
the Cover.
AL1702 E-9
USER CONTROLS
1
3
2
4
5
6
Front Panel Controls
1. Power Switch:
To turn ON or OFF the power.
2. PowerLED:
Lights up to indicate the power is turned ON.
3. Auto Adjust button / Exit:
1)When OSD menu is in active status, this button will act as EXIT-KEY (EXIT OSD menu).
2)When OSD menu is in off status, press this button for 2 seconds to activate the Auto
Adjustment function.
The Auto Adjustment function is used to set the HPos, VPos, Clock and Focus.
4. </Volume:
Activates the volume control when the OSD is OFF or navigate through adjustment icons
when OSD is ON or adjust a function when function is activated.
5. >/Volume:
Activates the volume control when the OSD is OFF or navigate through adjustment icons
when OSD is ON or adjust a function when function is activated.
6. MENU/ENTER:
Activate OSD menu when OSD is OFF or activate/de-activate adjustment function when
OSD is ON or Exit OSD menu when in Volume Adjust OSD status.
E-10 User’s Guide
HOW TO ADJUST A SETTING
1. Press the MENU-button to activate the OSD window.
2. Press < or > to select the desired function.
3. Press the MENU-button to select the function that you want to adjust.
4. Press < or > to change the settings of the current function.
5. To exit and save, select the exit function. If you want to adjust any other function, repeat
steps 2-4.
ADJUSTING THE PICTURE
The descriptions for function control LEDS
Main
Menu
Icon
Sub
Menu
Icon
Sub
Menu
Item
Description
Adjusts the contrast between the foreground and
background of the screen image.
Contrast
Brightness
Focus
Adjusts the background brightness of the screen
image.
Adjusts picture Focus
Adjusts picture Clock
Clock
AL1702 E-11
Main
Menu
Icon
Sub
Menu
Icon
Sub Menu Item
Description
H. Position
V. Position
Adjust the horizontal position.
Adjust the vertical position.
N/A
Warm
Cool
Set the color temperature to warm white.
Set the color temperature to cool white.
N/A
User /Red
User/Green
Adjusts Red/Green/Blue intensity.
User/Blue
English
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Deutsch
Francais
Espanol
Italiano
Multi-language selection.
E-12 User’s Guide
Main
Menu
Icon
Sub
Menu
Icon
Sub Menu Item
Description
H. Position
V. Position
Adjust the horizontal position of the OSD.
Adjust the vertical position of the OSD.
Adjust the OSD timeout.
OSD Timeout
Auto Config
Information
Auto Adjust the H/V Position, Focus and
Clock of picture.
N/A
Show the resolution, H/V frequency and
input port of current iput timing.
N/A
N/A
N/A
Clear each old status of Auto-
configuraation and set the color temperature
to Cool.
Reset
Exit
Save user adjustment and OSD disappear.
AL1702 E-13
TROUBLESHOOTING
Before sending your LCD monitor for servicing, please check the troubleshooting list
below to see if you can self-diagnose the problem.
Problems Current Status
Remedy
Using OSD, adjust brightness and contrast to
LED ON
maximum or reset to their default settings.
LED OFF
Check the power switch.
No
Picture
Check if AC power cord is properly connected
to the monitor.
LED displays
amber color
Check if video signal cable is properly
connected at the back of monitor.
Check if the power of computer system is ON.
Unstable Picture
Check if the specification of graphics adapter
and monitor is in compliance which may be
causing the input signal frequency mismatch.
Display is missing,
center shift, or too
small or too large
Using OSD, adjust RESOLUTION, CLOCK,
CLOCK-PHASE, H-POSITION and V-
POSITION with non-standard signals.
Abnormal
in display size
Picture
Using OSD, in case of missing full-screen image,
please select other resolution or other vertical
refresh timing.
Wait for a few seconds after adjusting the size of
the image before changing or disconnecting the
signal cable or powering OFF the monitor.
Abnormal No sound, or
Check the audio cable with the host PC is
connected.
Sound
sound level is too
low
Check if the volume setup of the host PC is in
minimum position and try to raise the volume
level.
E-14 User’s Guide
SPECIFICATION
Driving system
Size
TFT Color LCD
43.2cm(17.0")
0.264mm( H )x 0.264mm( V )
250cd/m2 (Typical)
400:1(Typical)
1400 (H) 1250 (V)
25 ms
Pixel pitch
Brightness
Contrast
LCD Panel
Viewable angle
Response time
Video
R,G,B Analog Interface
30KHz - 81KHz
55-75Hz
H-Frequency
V-Frequency
Display Colors
Dot Clock
16.2M Colors
135MHz
Max. Resolution
Plug & Play
1280 x 1024 @75Hz
VESA DDC/DDC2B
<45W
ON Mode
OFF Mode
EPA ENERGY STAR
< 3W
Input Connector
D-Sub 15pin
Analog:0.7Vp-p(standard),
75 OHM, Positive
Input Video Signal
Horizontal : 337.92mm
Vertical : 270.34mm
Maximum Screen Size
Power Source
100~240VAC,47~63Hz
AL1702 E-15
Operating Temp: 50 to 350C
Environmental Considerations
Storage Temp.: -200 to 600C
Operating Humidity: 10% to 85%
Dimensions
374(W) x 373(H) x 200(D)mm
4.6kg Unit (net)
Weight (N. W.)
Auto Adjust Key
>/ Volume
Switch
</Volume
Power Button
MENU/ Exit
Contrast
Brightness
Focus
Clock
H.Position
V.Position
External Controls:
Language
Functions
Auto configuration
(Warm) Color
(Cool) Color
RGB Color temperature
Reset
OSD position . timeout
Display information
Exit
Power Consumption ( Maximum )
Audio Output
45 Watts
Rated Power 1.5W rms (Per channel)
CUL, FCC, VCCI, CCC, MPR II,
CE, TUV/GS, TCO'99, UL,
ISO13406-2
Regulatory Compliance
* All specifications are subject to change without notice.
|