MICROWAVE OVEN BUILT-IN TRIM KIT
INSTALLATION INSTRUCTIONS
Built-In Trim Kit Models UMTK27, UMTK30
UL listed for use over built-in electric ovens:
27 (68.6 cm): MEW5527, MEW6527
30 (76.2 cm): MEW5530, MEW6530, JJW8130DD, JJW8330DD, JJW9130DD, JJW9330DD
Table of Contents
MICROWAVE OVEN SAFETY........................................................... 1
INSTALLATION INSTRUCTIONS ..................................................... 2
Tools and Parts............................................................................... 2
Location Requirements................................................................... 2
Minimum Cutout Dimensions......................................................... 2
Trim Kit Frame Dimensions ............................................................ 2
Electrical Requirements.................................................................. 3
Microwave Oven Preparation......................................................... 3
Duct Assembly................................................................................ 3
Microwave Oven Installation........................................................... 4
Install Top and Bottom Brackets.................................................... 4
Install Trim Kit Frame...................................................................... 4
MICROWAVE OVEN SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
You can be killed or seriously injured if you don't immediately
follow instructions.
DANGER
You can be killed or seriously injured if you don't
instructions.
follow
WARNING
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
W10308503A
Electrical Requirements
Microwave Oven Preparation
1. Unplug microwave oven before proceeding with installation.
2. Remove any loose items inside microwave oven.
WARNING
Duct Assembly
1. Remove 4 existing screws (2 on each side) from the
microwave oven. The screws are located at the lower edge.
These screws will be used in the next step.
2. Secure duct base to the microwave oven with the 4 existing
Electrical Shock Hazard
screws removed in Step 2.
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
A
B
Observe all governing codes and ordinances.
Required:
A. Duct base
B. Existing screws (4)
■
A 120 Volt, 60 Hz, AC only, 15- or 20-amp electrical supply
with a fuse or circuit breaker.
Recommended:
3. Secure left duct to outside panel of microwave oven with one
9/16" screw, as shown.
■
A time-delay fuse or time-delay circuit breaker.
■
A separate circuit serving only this microwave oven.
A
GROUNDING INSTRUCTIONS
■
For all cord connected appliances:
The microwave oven must be grounded. In the event of
an electrical short circuit, grounding reduces the risk of
electric shock by providing an escape wire for the electric
current. The microwave oven is equipped with a cord
having a grounding wire with a grounding plug. The plug
must be plugged into an outlet that is properly installed
and grounded.
B
A. Left duct
B. 9/16" screw
WARNING: Improper use of the grounding plug can
result in a risk of electric shock. Consult a qualified
electrician or serviceman if the grounding instructions are
not completely understood, or if doubt exists as to whether
the microwave oven is properly grounded.
Microwave Oven Installation
1. On the cutout floor, find and mark the centerline.
2. Use Template 1 to mark hole center for box screw. Be sure to
align the center line of template to center line of cutout floor.
Do not use an extension cord. If the power supply cord is
too short, have a qualified electrician or serviceman install
an outlet near the microwave oven.
SAVETHESE INSTRUCTIONS
14²⁵⁄₃₂"
(37.5 cm)
A
B
C
A. Cutout floor
B. Center line
C. Cutout opening
3. Using 7/64" drill, drill pilot hole into hole center marked in
Step 2.
3
4. Install the 3/16" screw, and leave 1/8" (3.2 mm) to 3/16"
NOTE: If Template 2 is missing or unusable, measure straight
up from upper end holes on bottom bracket, and mark the
new holes at 12¹⁵⁄₁₆" (32.9 cm) and 15²¹⁄₃₂" (39.8 cm). Make
sure the bottom bracket end holes and the new holes on each
side are plumb.
(4.7 mm) protruding from the cutout floor.
A
¹⁄₈" (3.2 mm) (min)
B
³⁄₁₆" (4.7 mm) (max)
C D
C D
D C
D C
TEMPLATE 2
12¹⁵⁄₁₆
(32.9 cm)
"
A. 3/16" screw
B. Cutout floor
15²¹⁄₃₂
"
(39.8 cm)
5. Slide microwave oven partway into cutout opening.
B A
A B
WARNING
5. Using 7/64" drill, drill pilot holes into the cabinet through holes
marked in Step 4, then remove template.
6. Position top bracket over pilot holes drilled in Step 5, then
secure with four 9/16" screws. (Illustration in this step shows
30" [76.2 cm] installation.)
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
A
B
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
C
D
6. Plug in microwave oven.
7. Make sure microwave oven is centered in the opening, and
slide it into place, engaging the 3/16" screw and duct base.
A. Top bracket
B. Cabinet
C. Cutout opening
D. Bottom bracket
Install Top and Bottom Brackets
1. Align bottom bracket to duct base, and mark 7 mounting
Install Trim Kit Frame
holes of bottom bracket, as shown.
30" (76.2 cm)
1. Position trim kit frame against the top and bottom brackets.
Make sure the trim kit frame makes contact with the cabinet.
2. Open microwave oven door, and secure trim kit frame using
4 painted 1/2" screws.
27" (68.6 cm)
A
B
2. Using 7/64" drill, drill pilot holes into the cabinet through holes
marked in Step 1.
3. Install bottom bracket to cabinet using seven 9/16" screws.
4. Position Template 2 over cabinet so that its reference holes (A)
(for 27" [68.6 cm] installation) or (B) (for 30" [76.2 cm]
installation) are over the upper end mounting holes of the
bottom bracket, as shown in following illustration. Tape the
template in place, then mark through holes (D) for 27"
(68.6 cm) installation, or through holes (C) for 30" (76.2 cm)
installation.
C
A. Trim kit frame
B. Microwave oven door (open)
C. Painted 1/2" screws (4)
Installation is now complete. Replace any loose items that have
been removed from microwave oven cavity.
Save these Installation Instructions for future reference.
W10308503A
SP PN W10308627A
DE68-03169C
4/10
Printed in Malaysia
© 2010
All rights reserved.
|