OWNER'S MANUAL
BND
ACD-88
CD-R/RW PLAYBACK
POWER
LOUD
M
LOC
EQ
AF TA
TP PTY
MP3 EQ
CDP EON
LOC REG
ST MONO
SW LOUD
D.DIR
A
N
EJECT
U
/
SEL
S
CLAS
POP
K
I
P
ROCK
T/F
MONO
OPEN
AS/PS
PAU
SCN
RPT
SHF
D.DN
D.UP
1
2
3
4
5
6
MODE
MUTE
SCN
ACD-88
AM/FM/MPX RADIO WITH
FOLD-DOWN REVERSIBLE FRONT PANEL,
COMPACT DISC PLAYER,
CD CHANGER CONTROLS
WIRELESS REMOTE CONTROL
AND QUARTZ CLOCK
Released 10-4-02.
TOLL-FREE INSTALLATION ASSISTANCE
The installation and wiring connections for this unit are so simple, we doubt you'll need our help, but, if you do,
we're here to help you. Just call our toll-free telephone assistance line at 1-800-645-4994 during the days and
hours shown (U.S.A. and Canada only).
TIME ZONE
MOUNTAIN
DAY
PACIFIC
CENTRAL
EASTERN
MON. - FRI.
SATURDAY
8:30AM - 7PM
9AM - 5PM
7:30AM - 6PM
8AM - 4PM
5:30AM - 4PM
6AM - 2PM
6:30AM - 5PM
7AM - 3PM
UNIVERSAL INSTALLATION USING MOUNTING SLEEVE
NUT (5MM)
PERFORATED STRAP
EXISTING DASH OPENING
FILE EDGES TO FIT IF NECESSARY - DO NOT OVERFILE
NOTE:IFDASHISSOLID, USEREARSIDE(WITHOUTTHELIP)OF
MOUNTING SLEEVE AS A TEMPLATE & CUT OPENING
FASTEN THIS END TO SCREW
STUD ON REAR OF CHASSIS
BEND TOP
TABS UPWARD
SCREW
(5MM)
BEND BOTTOM
TABS DOWNWARD
RADIO
SCREW STUD
NUT (5MM)
MOUNTING SLEEVE
FASTEN THIS END TO SECURE PART OF DASHBOARD.
DRILL HOLE IF NECESSARY.
REMOVALTOOLS
CAUTION:
FOR PROPER OPERATION OF THE CD PLAYER, THE CHASSIS
MUST BE MOUNTED WITHIN 20° OF HORIZONTAL. MAKE SURE
THE UNIT IS MOUNTED WITHIN THIS LIMITATION.
FOLD-DOWN
DETACHABLE
FRONT PANEL
20° MAX.
SIDE VIEW
OF
FRONT PANEL
CHASSIS
ISO INSTALLATION
TYPICAL INSTALLATION
REMOVE THE PLASTIC FRAME FROM THE FRONT OF
THE CHASSIS BY CAREFULLY UN-SNAPPING IT.
MAXIMUM
SCREW SIZE
M5 x 8
UN-SNAP AT 2 PLACES
EACH ON TOP AND BOTTOM
MAXIMUM
SCREW SIZE
M5 x 8
PLASTIC FRAME
3
FACTORY MOUNTING
BRACKETS
SPEAKER WIRING
RADIO WIRING
REFER TO PAGE 5 FOR SPEAKER WIRING
ANTENNA
AUTOMATIC
ANTENNA
CAR FUSEBLOCK
“RADIO” OR
“ACCESSORY”
FUSE
RED
0.5 AMP
FUSE
CAR
BATTERY
SCREW
BLACK
METAL PART OF DASH
(DRILL HOLE IF NECESSARY)
EXISTING ANTENNA
CABLE
YELLOW
IMPORTANT
THIS WIRE MUST BE
CONNECTED AS SHOWN
OR RADIO WILL NOT
OPERATE PROPERLY
20-PIN HARNESS
CONNECTOR
POSITIVE (+) TERMINAL
12-VOLTBATTERY
SEE PAGE 5 FOR
SPEAKER WIRING
20-PIN MATING
PLUG ON REAR
OF RADIO
ANTENNA SOCKET ON
REAR OF RADIO
10-AMP
PLUG-IN FUSE
4
SPEAKER WIRING
REFER TO PAGE 4
FOR RADIO WIRING
WARNING!
! THE AMPLIFIERS IN THIS RADIO ARE ONLY DESIGNED FOR USE WITH 4 SPEAKERS.
! NEVER COMBINE (BRIDGE) OUTPUTS FOR USE WITH 2 SPEAKERS.
! NEVER GROUND NEGATIVE SPEAKER LEADS TO CHASSIS GROUND.
! FAILURE TO WIRE EXACTLY AS SHOWN BELOW MAY CAUSE ELECTRICAL
NOTE: CHECK WITH YOUR RAMPAGE/AUDIOVOX CAR
STEREO SPECIALIST OR CALL 1-800-645-4994 FOR
RECOMMENDATIONS OF THE CHANGER MODELS THAT
WILL WORK WITH YOUR RADIO.
RCA AUXILIARY INPUT
JACKS FOR USE WITH
OPTIONAL EXTERNAL
STEREO CD PLAYER,
CASSETTE PLAYER, ETC.
RED------RIGHT REAR
WHITE---LEFT REAR
DIN CABLE (SUPPLIED
WITH CD CHANGER)
OPTIONAL CD CHANGER
6
COMPACT
8-PIN DIN SOCKET FOR
CONNECTION TO
OPTIONAL CD CHANGER
RADIO
RCA LINE OUT JACKS FOR
USE WITH OPTIONAL
EXTERNAL AMPLIFIERS
RED------RIGHT REAR
WHITE---LEFT REAR
20-PIN MATING
SOCKET
20-PIN INTERFACE
CONNECTOR
LEFT FRONT SPEAKER
RIGHT FRONT SPEAKER
SEE PAGE 4
FOR RADIO
WIRING
HELP!
1-800-645-4994
Monday - Friday
Saturday
8:30am-7:00pmEastern
9:00am-5:00pmEastern
5
LEFT REAR SPEAKER
RIGHT REAR SPEAKER
20
3, 4, 5, 6, 7
18
(BEHIND PANEL)
17, 33
12
28
13
1
8
10
BND
ACD-88
CD-R/RW PLAYBACK
POWER
LOUD
LOC
EQ
M
A
N
AF TA
TP PTY
MP3 EQ
CDP EON
LOC REG
ST MONO
SW LOUD
D.DIR
EJECT
11
21
22
36
37
U
/
SEL
S
CLAS
POP
K
I
P
ROCK
T/F
MONO
2
OPEN
AS/PS
PAU
SCN
RPT
SHF
D.DN
D.UP
1
2
3
4
5
6
MODE
MUTE
SCN
19
34
32
9
14
23
24
38
25
39
26
40
27
35
16
31
15
volume. The next press will select the bass
adjustment (BAS will appear on the display
panel). Pressing the button additional times
will select treble adjustment (TRB on the
display), balance (BAL), or fader (FAD). The
display will automatically return to the
normal indication 5 seconds after the last
adjustment or when another function is
activated.
1
POWER ON/OFF BUTTON (
)
Press this button to turn the unit on or off. If
the ignition switch is “on”, the unit will also
turn on automatically when a compact disc is
inserted, or if any other button is pressed.
2
AUDIO ADJUST CONTROL
To increase the volume level, press the Up
( ∧ ) button. The volume will increase and
the level will shown on the display panel from
a minimum of VOL 00 to a maximum of
VOL 100. To decrease the volume level,
press the Down ( ∨ ) button. The dis-
play will automatically return to the normal
indication 5 seconds after the last volume
adjustment or when another function is ac-
tivated. This control is also used in conjunc-
while the Equalizer function
NOTE: If the BAS or TRB functions arceuset
is
active, the Equalizer function will
automatically revert to the FLAT
setting.
4
BASS CONTROL
mode by pressing the SEL button
To adjust the bass level, first select3the Bass
so the
tion with the Select (SEL) button
3
to ad-
BAS indication appears on the display panel.
Within 5 seconds of choosing the Bass
mode, press the audio adjust Down button
els as described in
just the bass, treble,4balance and fader lev-
,
5
,
6
and
7
.
2
to decrease the bass response, or the
3
SELECT (SEL) BUTTON
Up button to increase it as desired.The level
will be shown on the display panel from a
minimum BAS 10 to a maximum of BAS 10
(BAS 00 indicates flat response). The display
will automatically return to the normal
This button is used to select the audio
function (volume, bass, treble, balance, or
fade) whose setting is adjusted using the
audio adjust Up/Down buttons 2. Pressing
the SEL button once will set the unit for
6
indication 5 seconds after the last button
adjustment or when another function is
activated.
3
so the FAD indication appears on
the display panel. Within 5 seconds of
choosing the Fader mode, press the audio
adjust Down button
2
to adjust the front-
5
TREBLE CONTROL
rear speaker balance to the front speakers
or the Up button to adjust it to the rear
speakers. The fader position will be shown
on the display panel from FAD 10R (full rear)
to FAD 10F (full front). When the level
between the front and rear speakers is equal,
F=R will be shown on the display panel. The
display will automatically return to the
normal indication 5 seconds after the last
adjustment or when another function is
activated.
Treble mode by pressing the SEL button
To adjust the treble level, first select t3he
so the TRB indication appears on the display
panel. Within 5 seconds of choosing the
Treble mode, press the audio adjust Down
button
2
to decrease the treble response
or the Up button to increase it as desired.
The level will be shown on the display panel
from a minimum TRB 10 to a maximum of
TRB 10 (TRB 00 indicates flat response).
The display will automatically return to the
normal indication 5 seconds after the last
adjustment or when another function is
activated.
8
LOUDNESS CONTOUR (LOUD)
When listening to music at low volume
levels, this feature will boost the bass and
treble ranges to compensate for the
characteristics of human hearing. Press and
hold the BND/LOUD button for more than 2
seconds to activate this feature; the LOUD
ON indication will appear on the display panel
for 5 seconds, and LOUD will also appear
and remain. Pressing the button again for
more than 2 seconds will deactivate the
feature (LOUD OFF indication will appear
on the display panel for 5 seconds, and
LOUD will also disappear).
6
LEFT/RIGHT BALANCE CONTROL
To adjust the left-right speaker balance, first
select the Balance mode by pressing the
SEL button 3 so the BAL indication appears
on the display panel. Within 5 seconds of
adjust Down button
choosing the Balanc2e mode, press the audio
to adjust the stereo
balance to the left channel speakers or the
Up button to adjust it to the right channel
speakers. The balance position will be shown
on the display panel from BAL 10L (full left)
to BAL 10R (full right). When the volume
level between the left and right speakers is
equal, L=R will be shown on the display
panel. The display will automatically return
to the normal indication 5 seconds after
the last adjustment or when another function
is activated.
9
AUDIO MUTE SELECTOR (MUTE)
Press this button momentarily to mute the
volume from the system ( MUTE will appear
blinking on the display panel). Pressing the
Up/Down buttons
button again or 2pressing the audio adjust
will return to the volume
level setting in use before the Mute function
was activated.
7
FRONT/REAR FADER CONTROL
During disc play, pressing this button will
mute disc audio and disc play will stop.
During this time, the
7
To adjust the front-rear speaker balance, first
select the Fader mode by pressing the SEL
indication will remain
signals, including weaker (more distant)
stations.
on the display panel to show that a disc is
still loaded in the unit.
bo
FM MONO/STEREO BUTTON (MONO)
bl
BAND SELECTOR (BND/LOUD)
During FM radio operation, this button is
used to select monaural or stereo reception
of the broadcast signal. Under normal
reception conditions, the unit should be left
in the stereo mode as indicated by the ST
indication on the display panel when tuned
to an FM stereo signal. If the stereo signal
is too noisy for comfortable listening, press
the MONO button to switch to monaural
reception (the ST indication will disappear
from the display panel and MONO will
appear). To return to stereo reception mode,
press the button again so that the ST
indication appears on the display panel.
Each time this button is pressed, the radio
band is changed. The indication AM, F1, F2
or F3 will appear on the display panel
according to your selection.
bm
MANU/SKIP (
To select a radio station, momentarily pess
the Up MANU/SKIP ( ) button to advance
the unit higher, or the Down MANU/SKIP
) button to tune lower within the selected
/
) BUTTONS
(
band. The radio will automatically tune to the
next strong station and stop on this
frequency. If the LOCAL mode is in effect,
the radio will seek the next local station and
stop at that frequency.
bp
PRE-SET SCAN (PS)
AUTO-STORE TUNING (AS)
Pressing either button for longer than 2
seconds will cause MANUAL to appear on
the display, accompanied by a beep tone,
thereby entering the seek mode. Pressing a
button in this mode will cause the radio to
rapidly tune in the up or down direction and
stop when the button is released. The radio
will then remain at that frequency. Five
seconds after Manual tune is inactive, AUTO
will momentarily appear for 2 seconds,
thereby reverting to the normal tuning mode.
Press this button momentarily to scan the
stations pre-set into the six memories of the
current band in use. The unit will stop at each
pre-set station for 5 seconds before
continuing to the next pre-set station (the
pre-set number on the display panel will flash
during Pre-Set Scan operation). Press the
button again momentarily to stop Pre-Set
Scan operation and remain on the selected
frequency.
Pressing and holding the button for longer
than 2 seconds will activate the Auto-Store
Tuning feature which will automatically scan
and enter up to 6 stations into the pre-set
memories of each FM band and the AM band.
If you have already set the pre-set memories
to your favorite stations, activating the Auto-
Store Tuning feature will erase those
stations and enter the new ones. This feature
is most useful when traveling in a new area
where you are not familiar with the local
stations.
bn
LOCAL (LOC) BUTTON
This feature is used to select the strength of
the signals at which the radio will stop during
Automatic Seek Tuning. Pressing the button
will select the Local setting (LOCAL will
appear on the display panel for 5 seconds
and LOC will remain to the right of the
frequency display) and only strong (local)
stations will be received. Pressing the button
again will select the Distant setting (Dx will
appear on the display panel for 5 seconds)
and the radio will stop at a wider range of
8
bq
STATION PRE-SET MEMORIES
the signal increases, the number of
illuminated segments will increase and vice-
versa.
To set any of the 6 pre-set memories in each
band, use the following procedure:
1. Turn the radio on and select the desired
band.
bu
MODE SELECTOR (MODE)
This button is used to select the CD player
or CD changer (if installed) playback mode,
auxiliary (AUX) input, or radio. Each press
of the button will select a different mode as
indicated on the display panel.
using the MANU/SKIP
controls.
2. Select the first station tbombe pre-set
tuning
3. Press the pre-set button to be set
and continue to hold it in for
approximately 2 seconds. The pre-
set number, will appear on the
display panel to the right of the
frequency indication and a single
beep will sound, indicating that the
station is now set into that pre-set
memory position. The station can
now be recalled at any time by
pressing that button.
During CD player operation, this button may
be used to change to radio, AUX input (MP3
or external CD player) or CD changer mode
without ejecting the disc. The DISC
indication will remain on the display panel
to show that the CD changer is operating.
Press the button again to return to return to
the desired mode.
cl
DISC SLOT
4. Repeat the above procedure for the
remaining 5 pre-sets on that band
and for the other 4 bands on the unit.
With the front panel in the fold-down position,
gently insert the disc into the slot (label
surface facing up) until the soft-loading
mechanism engages and pulls the disc in.
The S--CDP indication will appear on the
br
RADIO FREQUENCY SCAN
The current radio band can be scaned by
pressing the SCN button; as a result, the
radio will seek the stronger station
frequencies on the band in the upward
direction, and will stop at each of these
stations for 10 seconds before proceeding
display panel for 5 seconds.The (
indication illuminates and becomes
animated, the symbol lights, and the track
)
number appears on the display panel.
CAUTION: This unit is designed for play of
standard 5" (12cm) compact
discs ONLY. Do not attempt to
use 3" (8cm) CD-Singles in this
unit, either with or without an
adapter, as damage to the player
and/or disc can occur. Such
damage will not be covered by
the Warranty on this product.
on.
bs
LIQUID CRYSTAL DISPLAY (LCD)
The Liquid Crystal Display (LCD) panel
displays the frequency, time, and activated
functions.
bt
POWER LEVEL METER DISPLAY
This display consists of a left and right nine-
bar graph which provides a visual
representation of the audio signal level. As
cm
TRACK SELECT (
The Track Select function of the MANU SKIP
buttons are used to quickly access the
/
)
9
beginning of a particular track when a disc
is in play. Each time the Forward TRACK
cq
REPEAT PLAY SELECTOR (RPT)
During disc play, press this button to repeat
the play of the selected track (S--RPT will
appear on the display panel). Play of the
track will continue to repeat until the button
is pressed again and the S--RPT indication
disappears from the display panel. Repeat
Play mode will also be canceled by activating
Select (
) side of the button is pressed,
the next higher track number will be selected
as shown on the display panel. Similarly,
each time the Backward TRACK Select
(
) side of the button is pressed, the next
lower track number will be selected as shown
on the display panel.
the Track Scan
co
or Shuffle Play
cq
fcurnctions.
SHUFFLE PLAY SELECTOR (SHF)
cn
CUE/REVIEW FUNCTIONS
(
/
)
High-speed audible search to any section
of the disc can be made by the Cue and
Review functions of the MANU SKIP
buttons.Press and hold the Cue
During disc play, press this button to play the
tracks on the disc in a random shuffled order
(S--SHF will appear on the display panel). In
Shuffle Play mode, the TRACK Select function
will also select tracks in random order instead
ofthenormalprogression. TheShufflePlay mode
can be canceled by pressing the button again
(S--SHF indication will disappear from the display
(
) button to advance rapidly in the
forward direction (the advancing disc playing
time will be shown on the display panel), or
the Review (
) button to advance rapidly
in the backward direction (the decreasing
disc playing time will be shown on the
display panel)
cp
or
Track Scan
panel) or by caoctivating the Repeat Play
functions.
cs
DISC SELECT UP/DOWN
(D.UP/D.DN)
co
DISC PAUSE (PAU)
The Pause function is used to pause disc
play, whether it be the CD Player or the optional
CD Changer; S--PAUSE will appear on the
display. When pressed again, disc play will
resume from the point it was stopped and
S--PAUSE will disappear.
These buttons are used to select the desired
disc for play during changer operation. To ad-
vance to a higher number disc, press the D.UP
button, and to return to a lower number disc,
press the D.DN button. The number of the disc
in play will be shown on the display panel.
cp
TRACK SCAN SELECTOR (SCN)
ct
DISC EJECT (
)
During disc play, press this button to play
the first 10 seconds of each track on the
disc (S--SCN) will appear on the display
panel). When a desired track is reached,
press the SCN button again to cancel the
function (S--SCN will disappear from the
display panel) and play of the selected track
will continue.
Disc play is stopped and the disc is ejected
when this button is pressed. Radio or CD
changer operation will automatically resume
depending on which mode was in operation
prior to disc play. If the disc is not removed
from the unit within 15 seconds of being
ejected, it will automatically be re-loaded into
the unit to prevent it from being accidentally
damaged ( will appear on the display panel
to indicate that a disc is loaded in the player).
Scan mode will also cbpe
,
10
canceled by activating the Repeat Play
or Shuffle Play functions.
cq
Play of the disc can be resumed by using
dn
FRONT PANEL RELEASE BUTTON
(OPEN)
the MODE button
function.
bu
to choose the CD player
This button is used to release the
mechanism that holds the front panel to the
chassis. To fold down the front panel, press
the button so that the panel drops to the
lowered position. To reverse the panel and
show only a blank surface, grasp the panel
at the outer edge and press it up into
position. This will give the appearance that
no front panel exists. To return the front
panel to its normal position, press the
release button in the upper right corner of
the blank surface; the panel will then fold
down. Press in on the bottom edge to
reposition the panel in its normal playing
position.
cu
TIME/FREQUENCY SELECTOR (T/F)
During radio operation, press this button to
call the time display on the incorporated
quartz clock. The current time will appear
together with an A or P indication. The
display will return to the radio frequency
indication after 5 seconds.
During disc play press of this button to call
the time display. The display will return to
the disc indication after 5 seconds.
dl
EQUALIZER BUTTON (EQ)
The EQ button applies preset sound effects
to the unit’s audio output signal.The EQ
button, when pressed, will activate one of
the following operating modes ( CLASSICS,
POP M, ROCK M, DSP OFF or FLAT). Even
though the Equalizer function is active, as
displayed on the panel, if the bass and/or
treble level is set, the Equalizer function
automatically returns to the FLAT mode.
Conversely, when the Equalizer function is
not active, the unit returns to the user set
bass and treble levels.
do
REMOTE SENSOR
The sensor to detect the infrared signal from
the wireless remote control is located behind
the LCD display lens. For optimum operation
of the remote control, always aim the control
at the LCD display.
NOTES ON USE OF FRONT PANEL:
1.When the OPEN button is pressed in the
lower right corner of the front panel, the
panel folds down into the horizontal
position; in this position, compact discs
can be loaded into the CD player. Then
the panel can be returned to the normal
vertical position by pressing inward and
upward on the lower edge of the panel.
dm
RESET BUTTON
The Reset button is located to the right of
the SCN button on the front panel. The reset
circuitry should only be activated under the
following circumstances as it will erase
the time and pre-set memories:
2.To reverse the panel surface (the back of
the front panel), repeat step 1 above, and
raise the underside of the bottom edge,
folding the back side of the panel upward
so that the blank side of the panel is
facing outward. Press in until the panel
clicks into place.
1.Upon initial installation after all wiring is
completed.
2.If there is a malfunction of any of the
switches on the unit, pressing the Reset
button may clear the system and return
to normal operation.
11
3.To restore the front panel to its normal
operating position, press the release
button in the upper right corner of the
blank panel; the panel will then flip down
to expose the operating controls in the
horizontal position. Simply push in on
the bottom edge of this side to engage
the panel in its normal vertical position.
FRONT PANEL IN
NORMAL POSITION
FRONT PANEL
RELEASE (OPEN)
BUTTON
CD EJECT
BUTTON
(REF)
BND
ACD-88
CD-R/RW PLAYBACK
POWER
LOUD
M
LOC
EQ
AF TA
TP PTY
CDP EON
LOC REG
ST MONO
SW LOUD
D.DIR
A
N
EJECT
U
MP3 EQ
/
SEL
S
CLAS
POP
K
I
P
ROCK
T/F
MONO
OPEN
AS/PS
PAU
SCN
RPT
SHF
D.DN
D.UP
MODE
1
2
3
4
5
6
MUTE
SCN
CD EJECT BUTTON
DISC SLOT
RELEASE BUTTON
(BLANK SURFACE)
FRONT PANEL IN
REVERSE POSITION
PANEL IN FOLD-DOWN POSITION
SETTING THE CLOCK
1. Switch the vehicle ignition and radio “on”.
2. Press the Time/Frequency (T/F) button to call the time display.
3. Within 10 seconds, press and hold the T/F button until a single beep sounds and the
time display flashes.
4. With the display flashing, press the Up MANU/SKIP (
and A/P indication, or the Down MANU/SKIP (
the correct time.
) button to adjust the hours
) button to adjust the minutes to
5. Five seconds after the last hour or minute adjustment is made, the time will be set in
the unit and the display will return to the normal indication.
CD PLAYER ERROR CODES
If a problem should develop while operating the CD player, an error code (ER-1, ER-2,
ER-3, etc.) may appear on the display panel. This can indicate a number of problems
with the unit, including a mechanical error or an error in the microprocessor control of the
player. If an error code should appear, try ejecting and re-loading the disc into the player.
While the disc is out of the unit, make sure it is clean, undamaged, and loaded correctly
(label surface up). You may also try activating the RESET button dmon the unit, but this
will also erase the time and pre-set memories.
12
If the suggested measures do not solve the problem, contact an approved warranty
station near you for further assistance.
SPECIFICATIONS
Size:
7" W
x 2" H x 6-5/16" D
178 mm x 50 mm x 160 mm
Operating Voltage:
Fuse Ratings:
12 volts DC, negative ground
Constant (Yellow wire): 15 AMP.
Switched (Red wire): 0.5 AMP.
Output Power:
Output Wiring:
160 watts maximum
(40 watts x 4 channels)
Floating-ground type designed for 4 speaker use.
Front and rear channels CANNOT be combined
(bridged) for use with 2 speakers.
RCA low-level outputs (front and rear channels).
Output Impedance:
Low-Level Output:
Tuning Range:
Compatible with 4 – 8 ohm speakers.
500 mv.
AM: 530 – 1,720 kHz. (10 kHz. step)
FM: 87.5 – 107.9 MHz. (200 kHz. step)
Sensitivity:
AM: 20 uv.
FM: 1.5 uv.
FM Stereo Separation:
CD Frequency Response:
CD Signal/Noise Ratio:
CD Channel Separation:
CD Distortion:
>20 dB
17 – 20 kHz. +0/-3 dB
>65 dB
>60 dB
0.2%
*Specifications are subject to change without notice.
CD-RANDCD-RWPLAYBACKCAPABILITY
This model can play most CD-R and CD-RW media that contains audio programs.
Playbackof bothCD-RandCD-RW dependsontheconditionsof therecording equipment
and the CD-R or CD-RW disc quality. In some cases, a CD-R or CD-RW disc cannot be 13
played on this unit.
higher track number will be selected as
shown on the display panel. Similarly, each
CD CHANGER CONTROLS
Built into this radio are controls to operate
an optional CD changer. Please check with
your Rampage/Audiovox car stereo
specialist or call 1-800-645-4994 for
recommendations of the models that will
work with this radio.
time the Backward Track Select (
) button
is pressed, the next lower track number will
be selected as shown on the display panel.
ds
CUE/REVIEWFUNCTIONS
(
/
)
Adjustment of the audio functions (volume,
tone, balance, and fader) for the CD changer
operate in the same manner as they do for
radio play. The following controls will operate
the CD changer when it is installed and
connected to this radio. Refer to the owner’s
manual included with the CD changer for
instructions on the installation and correct
loading and use of the CD magazine.
High-speed audible search to any section of
the disc can be made by the Cue and Review
functions. Press and hold the Cue
(
) side of the button to advance rapidly
in the forward direction (disc play symbol
rotation on the display panel will increase)
or the Review (
) side of the button to
advance rapidly in the backward direction.
dt
TRACK/DISC SCAN SELECTOR
(SCN)
dp
CD CHANGER MODE SELECTOR
(MODE)
When the SCN button is pressed, the SCN
indication will appear on the display panel,
and the first 10 seconds of each track on
the disc will be played in order. When a
desired track is reached, press the SCN
button again and play of the selected track
will continue (SCN will disappear from the
display panel). The Track Scan mode will
also be canceled by activating the Repeat
or Shuffle Play function.
When the SCN button is pressed and
held, the DSN indication will appear on the
display panel and the first 10 seconds of the
first track on each disc in the magazine will
be played. When a desired disc is reached,
press the SCN button again and play of the
selected disc will continue (DSN will
disappear from the display panel). The Disc
Scan mode will also be canceled by
activating the Repeat Play or Shuffle Play
functions.
During radio or CD play, press this button
to select operation of the CD changer as
shown by CDC on the display panel. Disc
play will begin and the disc and track
number will be shown on the display panel.
When the magazine is loaded into the
changer, play will begin from the first track
of the first disc in the magazine.
dq
DISC SELECT (D.UP/D.DN)
These buttons are used to select the desired
disc for play. To advance to a higher number
disc, press the D.UP button. To return to a
lower number disc, press the D.DN button.
The number of the disc in play will be shown
on the display panel.
dr
TRACK SELECT (
/
)
The Track Select functions are used to
quickly access the beginning of a particular
track. Each time the Forward Track Select
14
(
) side of the button is pressed, the next
button will also select tracks in the shuffled
order instead of the normal progression. The
Shuffle Track mode can be canceled by
pressing the SHF button or by activating the
Scan or Repeat Play functions.
du
DISC/TRACK REPEAT PLAY (RPT)
When the RPT button is pressed, the RPT
indication will appear on the display panel
and play of the selected track will be
continually repeated until the Track Repeat
mode is canceled by pressing the RPT
button twice or by activating the Scan or
Shuffle Play functions.
When the SHF button is pressed and held,
the DSF indication will appear on the display
panel and the discs in the magazine will be
played in a random, shuffled order, as well
as the tracks on each disc. After playing all
tracks selected at random from a disc in
the magazine, the unit will select another
disc at random and play all the tracks on it
in a random shuffled order. This will continue
from disc-to-disc until the Random Disc
mode is canceled by pressing the SHF
button again or by activating the Scan or
Repeat Play functions.
When the Repeat button is pressed twice
the DRT indication will appear on the display
panel and play of the selected disc will be
continually repeated until the Disc Repeat
mode is canceled by pressing the RPT
button again or by activating the Scan or
Shuffle Play functions.
el
DISC/TRACK SHUFFLE PLAY (SHF)
When the SHF button is pressed, the SHF
indication will appear on the display panel
and the tracks on the disc will be played in a
random, shuffled order. The Track Select
CD CHANGER ERROR CODES
If a problem should develop while operating the CD changer, the following error codes may
appear on the display panel.
ER-1: Indicates that there is no magazine loaded in the CD changer.
ER-2: Indicates a problem with the magazine eject function.
ER-3: Indicates an error in the disc loading function.
ER-4: Indicates an error in the disc un-loading function.
ER-5: Indicates an error in the magazine position.
ER-6: Indicates an error in the laser pick-up position.
ER-7: Indicates an error in the laser focus on the disc.
In any of the above situations, try ejecting the CD magazine from the changer and make
sure the discs are clean, undamaged, and loaded correctly (refer to the Owner’s Manual
try activating the RESET button
memories.
If the suggested measures do not solve the problem, contact an approved warranty station
near you for further assistance.
of the CD changer). Re-load thedmmagazine and check for proper operation. You may also
on the unit, but this will also erase the time and pre-set
15
CD TRACK SELECT – See Main Unit
and except press
to select a higher track number,
WIRELESS REMOTE
CONTROL OPERATION
cm
dr
press
ber.
to select a lower track num
The wireless remote control supplied with
this model is capable of operating most
of the features of the unit from a remote
location. Each button on the remote con-
trol functions in the same way as the ref-
erenced button on the main unit. For op-
timal operation of the remote control, al-
cn
and
CD CdUsE/REVIEW – See Main Unit
except press
for Cue
function, and press
function.
for Review
wdoays aim it toward the Remote Sensor
on the front panel of the main unit.
7
8
9
bl
bm
bn
TIME/FREQUENCY (T/F) - See Main
Unit cu.
(AS/PS) - See Main Unit
AUTO SCAN/PRE-SET SbTpORE
.
1
2
PWR ON/OFF - See Main Unit
1
.
TRACK/DISC REPEAT (RPT) - See
Main Unit cqand du.
Main Unit
MODE SEbLuECTOR (MODE) - See
.
Unit
DISCcUsP SELECT (D.UP) - See Main
.
3
INFRARED SENDER - Emits infra-
red signal to radio which is detected
by the sensor do.
DISC DOWN SELECT (D.DN) - See
Main Unit cs.
BATTERYCOMPARTMENT - Holds one
3-Volt Button Cell for remote wireless
control operation.
4
Main Unit
2
,
VOLUME (LEV3EL)4CONTROL- See
,
5
,
6, and
7
.
5
6
Unit
3
,
4
,
SELECT BU5TTON (SEL) - See Main
,
6, and
7
.
bo
bp
bq
br
bs
TUNE/SEbEmK CONTROL – See Main
except
press
Main Unit
TRACK/DcISrC SHUFFLE (SHF) - See
and el.
Unit
RADIO PRE-SET MEMORY 1-6 - See
Main Unit bq.
TRACK/DISC PAUSE (PAU) - See Main
Unit co.
to increase frequency, and press
to decrease frequency.
MANUAL SEEK TUNING – See
Main Unit ,except press
bm
to Seek upward, press
to
Unit
cp
and
TRACK/DISdCtSCAN (SCN) - See Main
.
Seek downward.
AM/FM BAND(BAND)/ENTER SELEC-
TOR – See Main Unit bl.
16
1
3
3.Depending on the recording status,
conditions of the disc and the equip-
ment used for the recording, some CD-
Rs/CD-RWs may not be played on this
unit.
2
4
5
6
17
16
15
7
8
CARE AND MAINTENANCE
The radio section of your new sound system
does not require any maintenance. We recom-
mend you keep this manual for reference on the
many features found in this unit as well as how
to set the clock. The compact disc player section
also requires no routine maintenance, but proper
understanding of its use and handling will help
you obtain maximum enjoyment of its capabili-
ties. The following points should be observed:
14
13
9
10
! When cleaning the interior of the vehicle,
do not get water or cleaning fluids on the
unit.
11
! The CD player is a precision instrument
andwillnotoperateproperlyinextremehot
or cold. In case of such conditions, wait
untiltheinteriortemperatureofthevehicle
reaches a normal temperature before us-
ing the player.
12
NOTES ON DISCS:
Attempting to use non-standard shape
discs (e.g.; square, start, heart) may
damage the unit. Be sure to use round-
shape CDs only in this unit.
! If the temperature inside the player gets
too hot, a protective circuit will automati-
cally stop play of the disc. In this case,
allow the unit to cool off before operating
the player again.
NOTESONCD-Rs(RecordableCDs)/
CD-RWs(RewriteableCDs):
1.Be sure to use discs with the
following marks only for play in
this unit:
! Never insert anything other than a 5" (12
cm) compact disc into the player as the
mechanism can be damaged by foreign
objects.
! Donotattempttouse3"(8cm)CD-Single
discs in this unit, either with or without an
adaptor, as damage to the player and/or
disc may occur. Such damage will not be
covered by the Warranty on this product.
2.The unit cannot play a CD-R or
CD-RW that is not finalized. (Please
refer to the manual of your CD-R/CD-
RWsoftwareformoreinformationon
the finalization process.)
17
! When not using the disc player, always remove the compact disc.
! Whenthevehiclewarmsupduringcoldweatherorunderdampconditions,moisture
may condense on the lens of the disc player. Should this occur, the player will not
operateproperlyuntilthemoisturehasevaporated.
! TheunitisdesignedwithavibrationdampeningCDmechanismtominimizeinterruption
of disc play due to normal vibration in a moving vehicle. When driving on very rough
roads,however,occasionalsoundskipsmayoccur. Thiswillnotscratchordamage
the disc and normal play will resume when the rough conditions cease.
HANDLING COMPACT DISCS
Dirt, dust, scratches, and warpage can cause skips in the playback and deterioration
of sound quality. Please follow these guidelines to take care of your compact discs:
! Use only compact discs with the mark:
! Fingerprints, dust, and dirt should be carefully wiped off the disc’s playing surface
(shinyside)withasoftcloth. Wipeinastraightmotionfromtheinsidetotheoutside
of the disc.
! Neverusechemicalssuchasrecordsprays,household cleanersor thinner to clean
compact discs. Such chemicals can irreparably damage the disc’s surface.
! Discs should be kept in their storage cases when not in use.
! Do not expose discs to direct sunlight, high temperatures or high humidity for
extendedperiods.
! Do not stick paper, tape, or labels on the disc surfaces nor write on them with any
type of marker.
18
12 MONTH LIMITED WARRANTY
AUDIOVOX CORPORATION (the Company) warrants to the original retail purchaser of
this product that should this product or any part thereof, under normal use and conditions,
be proven defective in material or workmanship within 12 months from the date of original
purchase, such defect(s) will be repaired or replaced with new or reconditioned product
(at the Company's option) without charge for parts and repair labor.
To obtain repair or replacement within the terms of this Warranty, the product is to be
delivered with proof of warranty coverage (e.g. dated bill of sale), specification of
defect(s), transportation prepaid, to the warranty center at the address shown below.
This Warranty does not extend to the elimination of car static or motor noise, to correction
of antenna problems, to costs incurred for installation, removal, or reinstallation of the
product, or damage to tapes, compact discs, speakers, accessories, or vehicle electrical
systems.
This Warranty does not apply to any product or part thereof which, in the opinion of the
Company, has suffered or been damaged through alteration, improper installation,
mishandling, misuse, neglect, accident, or by removal or defacement of the factory serial
number/bar code label(s). THE EXTENT OF THE COMPANY'S LIABILITY UNDER THIS
WARRANTYISLIMITEDTOTHEREPAIRORREPLACEMENTPROVIDEDABOVEAND,
INNOEVENT,SHALL THE COMPANY'S LIABILITY EXCEED THE PURCHASE PRICE
PAID BY PURCHASER FOR THE PRODUCT.
This Warranty is in lieu of all other express warranties or liabilities. ANY IMPLIED
WARRANTIES,INCLUDINGANYIMPLIEDWARRANTYOFMERCHANTABILITY,SHALL
BE LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY. ANY ACTION FOR
BREACHOFANYWARRANTYHEREUNDERINCLUDINGANYIMPLIEDWARRANTYOF
MERCHANTABILITY MUST BE BROUGHT WITHIN A PERIOD OF 30 MONTHS FROM
DATEOFORIGINALPURCHASE. INNOCASESHALLTHECOMPANYBELIABLEFOR
ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY
OTHERWARRANTY,EXPRESSORIMPLIED,WHATSOEVER. Nopersonorrepresentative
is authorized to assume for the Company any liability other than expressed herein in
connection with the sale of this product.
Some states do not allow limitations on how long an implied warranty lasts or the
exclusion or limitation of incidental or consequential damage so the above limitations
or exclusions may not apply to you. This Warranty gives you specific legal rights and you
may also have other rights which vary from state to state.
U.S.A.: AUDIOVOX CORPORATION, 150 MARCUS BLVD., HAUPPAUGE, NY 11788 !1-800-645-4994
CANADA: CALL 1-800-645-4994 FOR LOCATION OF WARRANTY STATION SERVING YOUR AREA
22
19
128-4270E
© 2002 Audiovox Electronics Corp., Hauppauge, NY 11788
Printed in China
23
20
128-6508
|