Read all instructions BEFORE assembly and USE of product.
KEEP INSTRUCTIONS FOR FUTURE USE.
Model #1305
R
SNAP N GO
Instruction Manual
Convenience through innovation and thoughtful design
10.05
Rear Axle
Parent Tray
Front Wheels
Stroller
TO ENSURE SAFE OPERATION OF YOUR STROLLER, PLEASE FOLLOW THESE
INSTRUCTIONS CAREFULLY. RETAIN THESE INSTRUCTIONS FOR FUTURE
REFERENCE.
ASSEMBLY:
• Remove stroller from box. The front wheels, rear wheels and
parent tray need to be installed prior to use.
• To attach the front wheels, unfold stroller as described in the
section following. See figure 1. Lean the stroller backwards so
that it rests on the handle and rear frame tubes and the front wheel
bayonet are pointing upward. Position the front wheel assembly
at the front wheel bayonet such that the swivel assembly will slide
Figure 1.
onto the front wheel bayonet. Push each front wheel assembly
onto the front wheel bayonet until snapped into place. Pull on
the wheel assembly to ensure that it is securely attached to the
stroller. Please see figure 2.
Push onto
bayonet
• Lean the stroller forward to rest on the front wheels. To attach
the rear wheels, position the rear axle and wheel assembly such
that the brake levers are facing to the rear of the stroller. Press the
rear wheel assembly onto the rear frame tubes being careful that
the push buttons on the forward side of each rear tube engage the
hole on the forward side of each rear wheel housing. Pull on the
rear wheel assembly to ensure that it is securely attached to the
stroller. Please see figure 3.
Figure 2.
Ensure that the wheels are firmly locked into place. Do Not use the
stroller if the wheels are not locked into place, but rather contact
our customer service department immediately at (800) 328-7363,
between the hours of 8:00am and 4:30pm PCT, for assistance.
Figure 3.
2
• To attach the parent tray, position the tray so that the hinges for the
storage compartment are facing foward. Attach one end at a time by
locating the fitting at the top of the frame and the hole on the side
of the parent tray, snap together. Repeat for other side. Check that
the tray is securely latched in place. Please see figure 4. To remove
parent tray, reverse the installation steps.
WARNING: Do not place hot
liquids in the parent tray. Hot liquids
can burn your child. Do not place more
than 3 pounds in the tray as it may cause a
hazardous unstable condition to exist.
Figure 4.
WARNING:Avoid serious injury
from falling or sliding out. Always use the
Infant Car Seat harness.
Figure 5.
BRAKES
WARNING:Always set brakes
when the stroller is not being pushed so that
the stroller will not roll away. Never leave
stroller unattended on a hill or incline as the
stroller may slide down the hill.
Figure 6.
• To engage brakes, apply light downward pressure to the brake lever
located on each rear wheel. The stroller may require slight forward
or rearward movement in order to line up the teeth on the brake
with the each wheel brake cluster. See figure 5. Check that the
stroller will not move and that the brakes are properly applied. To
release, gently lift up on the brake lever.
LOCK
UNLOCK
TO FOLD STROLLER:
Do Not allow children near stroller while folding.
• To fold the stroller slide the red handle in the center of the handle to
the left and squeeze while pushing forward on the handle. Once the
stroller begins to fold, release the red handle and pull backward on
the front frame until stroller is folded. Please see figure 6. Secure
the stroller in the folded position by latching the fold latch, located
on the right side of the stroller at the intersection of the handle
and the rear tube, over the extended rivet on the lower frame tube.
Please see figure 7.
Figure 7.
Figure 8.
3
TO UNFOLD STROLLER:
Do Not allow children near stroller while unfolding.
• Release the folding latch, which is located on the right side. See
figure 8.
• Lift up on the stroller handle with both hands until the stroller frame
is erect and locked in the open position. See figure 9. The stroller
has spring-loaded latches on both sides of the frame. Test that both
latches are fully engaged prior to placing your child in the stroller.
Figure 9.
TO ATTACH AN INFANT CAR SEAT
• Place car seat onto front bar. See figure 10. NOTE: Some brands
of infant car seats will lock onto the front bar, and some brands
may simply rest on the front bar, You must ALWAYS use the
safety belt to secure every car seat that is placed on the snap n
go.
• Make sure the front of the car seat rests on the red support tabs located
on the frame. See figure 11. NOTE: For wider car seats there is a
higher support tab located above the main red support tabs.
• Strap the safety belt over the carseat and connect the buckles together.
Tighten the strap so the car seat fits snug and can't move. See figure
12. NOTE: Some car seats have slots for the safety belt to slide
through, if you have a car seat with these slots please feed the
safety belt through each slot and secure. See figure 13
Figure 10.
FRONT
SUPPORT
TAB
WARNING:Avoid serious injury
from falling, ALWAYS use the safety belt
to secure carseat to stroller.
Figure 11.
Figure 12.
Figure 13.
IF YOU EXPERIENCE ANY DIFFICULTY IN USING THIS PRODUCT,
PLEASE CONTACT OUR CUSTOMER SERVICE DEPARTMENT AT (800) 328-7363
BETWEEN THE HOURS OF 8:00AM AND 4:30PM PACIFIC COAST TIME FOR ASSISTANCE.
4
|