Behringer Music Mixer PMP518M User Manual

User Manual

EUROPOWER PMP518M

Ultra-Compact 180-Watt 5-Channel Powered Mixer with

Multi-FX Processor and FBQ Feedback Detection System

behringer.com

EUROPOWER PMP518M User Manual

9. Do not defeat the safety purpose of the polarized

or grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding-type plug

has two blades and a third grounding prong. The wide

blade or the third prong are provided for your safety. If the

provided plug does not ﬁt into your outlet, consult an

electrician for replacement of the obsolete outlet.

Limited Warranty

§ 1 Warranty

[1] This limited warranty is valid only if you purchased

the product from a BEHRINGER authorized dealer in the

country of purchase. A list of authorized dealers can be

found on BEHRINGER’s website behringer.com under

“Where to Buy“, or you can contact the BEHRINGER oﬃce

closest to you.

Important Safety

Instructions

10. Protect the power cord from being walked on or

pinched particularly at plugs, convenience receptacles,

and the point where they exit from the apparatus.

Terminals marked with this symbol carry

electrical current of suﬃcient magnitude to

constitute risk of electric shock. Use only

[2] MUSIC Group* warrants the mechanical and

electronic components of this product to be free of defects

in material and workmanship if used under normal

operating conditions for a period of one (1) year from

the original date of purchase (see the Limited Warranty

11. Use only attachments/accessories speciﬁed by

the manufacturer.

high-quality commercially-available speaker cables with

1" TS plugs pre-installed. All other installation or

modiﬁcation should be performed only by

qualiﬁed personnel.

12. Use only with the

cart, stand, tripod, bracket, terms in § 4 below), unless a longer minimum warranty

or table speciﬁed by the period is mandated by applicable local laws. If the product

manufacturer, or sold with shows any defects within the speciﬁed warranty period

the apparatus. When a cart and that defect is not excluded under § 4, MUSIC Group

is used, use caution when shall, at its discretion, either replace or repair the product

moving the cart/apparatus using suitable new or reconditioned product or parts.

This symbol, wherever it appears, alerts you

to the presence of uninsulated dangerous

voltage inside the enclosure - voltage that

may be suﬃcient to constitute a risk of shock.

combination to avoid

In case MUSIC Group decides to replace the entire product,

this limited warranty shall apply to the replacement

product for the remaining initial warranty period, i.e.,

one (1) year (or otherwise applicable minimum warranty

period) from the date of purchase of the original product.

This symbol, wherever it appears, alerts you injury from tip-over.

to important operating and maintenance

instructions in the accompanying literature.

Please read the manual.

13. Unplug this apparatus during lightning storms or

when unused for long periods of time.

14. Refer all servicing to qualiﬁed service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power supply cord or plug

is damaged, liquid has been spilled or objects have fallen

into the apparatus, the apparatus has been exposed

to rain or moisture, does not operate normally, or has

been dropped.

[3] Upon validation of the warranty claim, the repaired

or replacement product will be returned to the user freight

prepaid by MUSIC Group.

Caution

To reduce the risk of electric shock, do not

remove the top cover (or the rear section).

No user serviceable parts inside. Refer servicing to

qualiﬁed personnel.

[4] Warranty claims other than those indicated above

are expressly excluded.

PLEASE RETAIN YOUR SALES RECEIPT. IT IS YOUR PROOF

OF PURCHASE COVERING YOUR LIMITED WARRANTY.

THIS LIMITED WARRANTY IS VOID WITHOUT SUCH PROOF

OF PURCHASE.

Caution

15. The apparatus shall be connected to a MAINS socket

outlet with a protective earthing connection.

To reduce the risk of ﬁre or electric shock,

do not expose this appliance to rain and

moisture. The apparatus shall not be exposed to dripping

16. Where the MAINS plug or an appliance coupler is

or splashing liquids and no objects ﬁlled with liquids, such used as the disconnect device, the disconnect device shall

§ 2 Online registration

as vases, shall be placed on the apparatus.

remain readily operable.

Please do remember to register your new BEHRINGER

equipment right after your purchase at behringer.com

under“Support”and kindly read the terms and conditions

of our limited warranty carefully. Registering your

purchase and equipment with us helps us process

your repair claims quicker and more eﬃciently.

Thank you for your cooperation!

Caution

These service instructions are for use

by qualiﬁed service personnel only.

To reduce the risk of electric shock do not perform any

servicing other than that contained in the operation

instructions. Repairs have to be performed by qualiﬁed

service personnel.

§ 3 Return materials authorization

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

[1] To obtain warranty service, please contact the

retailer from whom the equipment was purchased.

Should your BEHRINGER dealer not be located in your

vicinity, you may contact the BEHRINGER distributor for

your country listed under“Support”at behringer.com.

If your country is not listed, please check if your problem

can be dealt with by our“Online Support”which may

also be found under“Support”at behringer.com.

Alternatively, please submit an online warranty claim at

behringer.com BEFORE returning the product. All inquiries

must be accompanied by a description of the problem

and the serial number of the product. After verifying

the product’s warranty eligibility with the original sales

receipt, MUSIC Group will then issue a Return Materials

Authorization (“RMA”) number.

Legal Disclaimer

Technical speciﬁcations and appearance are subject to change without

notice. The information contained herein is correct at the time of printing.

All trademarks are the property of their respective owners. MUSIC Group

accepts no liability for any loss which may be suﬀered by any person

who relies either wholly or in part upon any description, photograph or

statement contained herein. Colors and speciﬁcations may vary slightly from

product. BEHRINGER products are sold through authorized dealers only.

Distributors and dealers are not agents of MUSIC Group and have absolutely

no authority to bind MUSIC Group by any express or implied undertaking

or representation. This manual is copyrighted. No part of this manual may

be reproduced or transmitted in any form or by any means, electronic or

mechanical, including photocopying and recording of any kind, for any

purpose, without the express written permission of Red Chip Company Ltd.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as

radiators, heat registers, stoves, or other apparatus

(including ampliﬁers) that produce heat.

Trident Chambers, Wickhams Cay, P.O. Box 146,

Road Town, Tortola, British Virgin Islands

behringer.com

EUROPOWER PMP518M User Manual

[2] Subsequently, the product must be returned in

its original shipping carton, together with the return

authorization number to the address indicated by

MUSIC Group.

§ 9 Amendment

[7] Any repair or opening of the unit carried out by

unauthorized personnel (user included) will void the

limited warranty.

Warranty service conditions are subject to change without

notice. For the latest warranty terms and conditions

and additional information regarding MUSIC Group’s

limited warranty, please see complete details online at

behringer.com.

[8] If an inspection of the product by MUSIC Group

shows that the defect in question is not covered by the

limited warranty, the inspection costs are payable by

the customer.

[3] Shipments without freight prepaid will not

be accepted.

* MUSIC Group Macao Commercial Oﬀshore Limited of

Rue de Pequim No. 202-A, Macau Finance Centre 9/J, Macau,

including all MUSIC Group companies

§ 4 Warranty Exclusions

[9] Products which do not meet the terms of this

limited warranty will be repaired exclusively at the buyer’s

expense. MUSIC Group or its authorized service center will

inform the buyer of any such circumstance. If the buyer

fails to submit a written repair order within 6 weeks after

notiﬁcation, MUSIC Group will return the unit C.O.D. with

a separate invoice for freight and packing. Such costs will

also be invoiced separately when the buyer has sent in a

written repair order.

[1] This limited warranty does not cover consumable

parts including, but not limited to, fuses and batteries.

Where applicable, MUSIC Group warrants the valves or

meters contained in the product to be free from defects in

material and workmanship for a period of ninety (90) days

from date of purchase.

[2] This limited warranty does not cover the product

if it has been electronically or mechanically modiﬁed

in any way. If the product needs to be modiﬁed or

adapted in order to comply with applicable technical

or safety standards on a national or local level, in any

country which is not the country for which the product

was originally developed and manufactured, this

modiﬁcation/adaptation shall not be considered a defect

in materials or workmanship. This limited warranty does

not cover any such modiﬁcation/adaptation, regardless

of whether it was carried out properly or not. Under the

terms of this limited warranty, MUSIC Group shall not

be held responsible for any cost resulting from such a

modiﬁcation/adaptation.

[10] Authorized BEHRINGER dealers do not sell new

products directly in online auctions. Purchases made

through an online auction are on a“buyer beware”basis.

Online auction conﬁrmations or sales receipts are not

accepted for warranty veriﬁcation and MUSIC Group will

not repair or replace any product purchased through an

online auction.

§ 5 Warranty transferability

This limited warranty is extended exclusively to the

original buyer (customer of authorized retail dealer) and

is not transferable to anyone who may subsequently

purchase this product. No other person (retail dealer, etc.)

shall be entitled to give any warranty promise on behalf

of MUSIC Group.

[3] This limited warranty covers only the product

hardware. It does not cover technical assistance for

hardware or software usage and it does not cover

any software products whether or not contained in

the product. Any such software is provided“AS IS”

unless expressly provided for in any enclosed software

limited warranty.

§ 6 Claim for damage

Subject only to the operation of mandatory applicable

local laws, MUSIC Group shall have no liability to the buyer

under this warranty for any consequential or indirect

loss or damage of any kind. In no event shall the liability

of MUSIC Group under this limited warranty exceed the

invoiced value of the product.

[4] This limited warranty is invalid if the factory-

applied serial number has been altered or removed from

the product.

[5] Free inspections and maintenance/repair work

are expressly excluded from this limited warranty, in

particular, if caused by improper handling of the product

by the user. This also applies to defects caused by normal

wear and tear, in particular, of faders, crossfaders,

potentiometers, keys/buttons, guitar strings, illuminants

and similar parts.

§ 7 Limitation of liability

This limited warranty is the complete and exclusive

warranty between you and MUSIC Group. It supersedes

all other written or oral communications related to this

product. MUSIC Group provides no other warranties for

this product.

[6] Damage/defects caused by the following conditions

are not covered by this limited warranty:

§ 8 Other warranty rights and

national law

[1] This limited warranty does not exclude or limit the

•

improper handling, neglect or failure to operate the

unit in compliance with the instructions given in

BEHRINGER user or service manuals;

buyer’s statutory rights as a consumer in any way.

[2] The limited warranty regulations mentioned herein

are applicable unless they constitute an infringement of

applicable mandatory local laws.

•

connection or operation of the unit in any way

that does not comply with the technical or safety

regulations applicable in the country where the

product is used;

[3] This warranty does not detract from the seller’s

obligations in regard to any lack of conformity of the

product and any hidden defect.

•

damage/defects caused by acts of God/Nature

(accident, ﬁre, ﬂood, etc) or any other condition that

is beyond the control of MUSIC Group.

behringer.com

EUROPOWER PMP518M User Manual

1. Introduction

1.1.3 Online registration

Right from the very start it has been our goal to design a revolutionary unit that

can be used for a wide variety of applications. And indeed, this overwhelming

power mixer gives you plenty of functionality and a broad range of connection

and expansion options.

Please register your new BEHRINGER equipment right after your purchase

by visiting http://behringer.com and read the terms and conditions of our

warranty carefully.

Should your BEHRINGER product malfunction, it is our intention to have it

repaired as quickly as possible. To arrange for warranty service, please contact

the BEHRINGER retailer from whom the equipment was purchased. Should your

BEHRINGER dealer not be located in your vicinity, you may directly contact

one of our subsidiaries. Corresponding contact information is included in the

original equipment packaging (Global Contact Information/European Contact

Information). Should your country not be listed, please contact the distributor

nearest you. A list of distributors can be found in the support area of our website

(http://behringer.com).

1.1 Before you get started

1.1.1 Shipment

Your EUROPOWER was carefully packed at the factory and the packaging is

designed to protect the unit from rough handling. Nevertheless, we recommend

that you carefully examine the packaging and its contents for any signs of

physical damage which may have occurred during transit.

◊

If the unit is damaged, please do NOT return it to BEHRINGER,

but notify your dealer and the shipping company immediately.

Otherwise, claims for damage or replacement may not be granted.

Registering your purchase and equipment with us helps us process your repair

claims more quickly and eﬃciently.

Thank you for your cooperation!

◊

We recommend that you use a ﬂight case, so as to give your power

mixer optimum protection during use or transport.

Always use the original packing carton to prevent damage during

storage or transport.

Make sure that children cannot play unsupervised with the device

or its packaging.

Please ensure proper disposal of all packing materials.

1.1.2 Initial operation

Be sure that there is enough air space around the unit for cooling and, to avoid

overheating, please do not place the EUROPOWER near radiators, etc.

◊

Blown fuses must be replaced by fuses of the same type and rating!

Please refer to the “Speciﬁcations” for details.

The mains connection is made using the enclosed power cord and a standard IEC

receptacle. It meets all of the international safety certiﬁcation requirements.

◊

Please make sure that all units have proper ground connection.

For your own safety, never remove or disable the ground conductor

from the unit or on the AC power cord.

◊

The sound quality may diminish within the range of powerful

broadcasting stations and high-frequency sources. Increase the

distance between the transmitter and the device and use shielded

cables for all connections.

behringer.com

EUROPOWER PMP518M User Manual

2. Control Elements

[1] [3] [4]

[12] [9] [10] [11]

[13]

[17]

[2]

[5]

[8]

[7] [6]

Fig. 2.1: Front panel control elements and connectors

2.1 Input channels

[19] [20] [21] [14] [16] [15] [18]

[22]

2.3 Main section

[1] The HIGH control in the EQ section governs the high-frequency range of the [13] Your power mixer is equipped with a graphic 7-band equalizer.

respective channel.

Use the EQ to adjust the sound to the room acoustics.

[2] The LOW control allows you too boost/cut the low-frequency range.

[14] Press the FBQ IN switch to activate the FBQ Feedback Detection System.

The frequencies causing feedback are shown by the brightly lit fader LEDs.

Simply lower the level of the respective frequency range until feedback

disappears and the LED goes out.

[3] The FX control determines the signal level sent from each channel to the

built-in eﬀects processor.

◊

Please note that the eﬀects processor signal will be inaudible when the

FX LEVEL control ([15]) is set fully counter-clockwise.

[15] Turn the FX LEVEL control to add eﬀect to the main mix. When it is fully

counterclockwise, no eﬀect signal is added.

[4] The LEVEL control adjusts the channel signal level in the main mix.

[16] The CD/tAPE IN control adjusts the volume of the CD/TAPE IN signal (see [19]).

[5] The CLIP LED is very useful to control the input gain. It should never be

[17] Use this 5-digit LED meter to control the output level of the main signal.

The upper LIM LED illuminates when the internal amp protection circuit

responds to output levels that are too high.

constantly illuminated (only with signal peaks).

[6] The PAD switch reduces the input sensitivity of the channel by approx.

30 dB, to connect for example line-level signals.

[18] The MAStER control is used to adjust the main output volume.

[7] The balanced LINE IN input (1" TRS) can be used for line-level signal

sources, e.g. keyboards.

2.3.1 Connectors

[8] Each channel has a balanced MIC microphone input with XLR connectors.

[19] The CD/tAPE IN connector (RCA) allows you to feed in external stereo

signals, e.g. from a CD player, tape deck or other line-level source.

◊

Please remember to use either the microphone or the line input of a

channel at a time, but never both at the same time!

[20] The REC OUt (RCA) provides line-level signals from the power mixer to a

DAT recorder, for example (two identical mono signals).

2.2 Eﬀects section

◊

If the REC OUT signal is connected to a recorder whose output signal

is returned to the CD/TAPE IN, feedback can occur when you activate

the record function. So, disconnect the CD/TAPE IN from the recorder,

before you start recording!

[9] Be sure that the CLIP LED illuminates for signal peaks only. If it is illuminated

all the time, it is a sign that the eﬀects processor is overloading and hence

producing unpleasant distortion. The SIG LED below illuminates when the

eﬀects processor receives an input signal.

[21] The PMP518M features an AMP INSERt connector for diﬀerent applications.

You can use just the power stage of the mixer for connecting a preamp for

example. For this application you can use a 1" TS connector where the signal

is sent over the tip of the plug. Additionally you can use the AMP INSERT

as output, so you can use just the mixer section and connect a separate

power amp here. For this application you have to use a 1" TRS connector,

because the signal is send over the ring of the plug.

[10] The EFFECt display shows the currently selected preset.

[11] Turn the PROGRAM control to select an eﬀects preset

(preset number starts ﬂashing). Push the control brieﬂy to

conﬁrm your selection.

[12] Press the FX IN button to activate the eﬀects processor.

[22] Use the POWER switch to put the unit into operation. The POWER switch

should always be in the “Oﬀ” position when you are about to connect the

unit to the mains.

◊

Please note: The POWER switch does not fully disconnect the unit from

the mains. Unplug the power cord completely when the unit is not used

for prolonged periods of time.

behringer.com

EUROPOWER PMP518M User Manual

[24]

{25]

[23]

[27]

[26]

Fig. 2.2: Rear panel control elements and connectors

2.4 Rear panel

[23] The mains connection is on a standard IEC receptacle. An appropriate power

4. Installation

4.1 Mains connection

cord is supplied with the unit.

Blown fuses must be replaced by fuses of the same type and rating.

[24] FUSE HOLDER. Before connecting the unit to the mains, ensure that

the voltage setting matches your local voltage. Blown fuses should only

be replaced by fuses of the same type and rating. Please also read the

information given in chapter 6 “Speciﬁcations”.

The mains connection is made using the enclosed power cord and a standard IEC

receptacle. It meets all of the international safety certiﬁcation requirements.

◊

Please make sure that all units have a proper ground connection.

For your own safety, never remove or disable the ground conductor

from the unit or of the AC power cord.

[25] The three PARALLEL SPEAKER OUtPUts provide the mono main signal on

a Neutrik Speakon-compatible connector (pins 1+/1- and 2+/2-) and on two

1" TS connectors.

4.2 Audio connections

◊

The impedance of the loudspeaker connected must not fall below 4 Ω.

The inputs and outputs of the BEHRINGER EUROPOWER are unbalanced

1" TS connectors — except for the balanced mono line inputs and the

balanced XLR inputs. Of course, all inputs and outputs work with both balanced

and unbalanced connectors. The Tape Ins and Outs are on RCA connectors.

Information on how to properly connect your speaker with regard to

polarity can be found on the rear of the mixer (PINOUTs).

[26] This is the cooling fan of the unit.

[27] SERIAL NUMBER.

◊

Please ensure that only qualiﬁed personnel install and operate the

power mixer. During installation and operation, the user must have

suﬃcient electrical contact to earth. Electrostatic charges might aﬀect

the operation of the unit.

3. Digital Eﬀects Processor

100 FIRST-CLASS EFFECTS

Unbalanced ¼" TS connector

Strain relief clamp

Sleeve

The PMP518M features a built-in digital eﬀects processor. This eﬀects processor

oﬀers a large number of standard eﬀects such as Hall, Chorus, Flanger, Delay and

various combination eﬀects. Using the FX control, you can feed signals into the

eﬀects processor. The integrated eﬀects module has the advantage of requiring

no wiring. This way, the danger of creating ground loops or uneven signal levels

is eliminated at the outset, completely simplifying the handling.

Tip

Presets 00 - 09:

Presets 10 - 19:

Presets 20 - 29:

Presets 30 - 39:

Presets 40 - 49:

Presets 50 - 59:

Presets 60 - 69:

Presets 70 - 79:

Presets 80 - 89:

Presets 90 - 99:

Hall

Room

Plate

Sleeve

(ground/shield)

Gated/Reverse

Early Reﬂections

Delay

Tip

(signal)

Chorus

Phase/Pitch

Multi 1

Fig. 4.1: 1" TS connector

Multi 2

behringer.com

EUROPOWER PMP518M User Manual

Balanced ¼" TRS connector

strain relief clamp

tip

sleeve

ring

tip

sleeve

shield

Fig. 4.4: RCA cable

4.3 Loudspeaker connection

sleeve

Your EUROPOWER is equipped with high-quality Neutrik Speakon-compatible

loudspeaker connectors, which ensure safe and trouble-free operation.

The Speakon connector was especially developed for high-power loudspeakers.

Once it is plugged in, it safely locks into position and cannot be accidentally

disengaged. It prevents the occurrence of electrical shock and ensures the

correct polarity. Each of the connectors carries only the assigned single signal

(see tab. 4.1/ﬁg. 4.5 and the information on the rear panel of the power mixer).

ground/shield

ring

cold (-ve)

tip

hot (+ve)

For connection of balanced and unbalanced plugs,

ring and sleeve have to be bridged at the stereo plug.

Professional speaker connector

(compatible with Neutrik Speakon connectors)

Fig. 4.2: 1" TRS connector

Balanced use with XLR connectors

front view

rear view

input

1 = ground/shield

2 = hot (+ve)

Fig. 4.5: Loudspeaker connector

3 = cold (-ve)

Please be sure to only use commercial Speakon cables (type NL4FC) for

connecting your loudspeakers to the mixer. Please check the pin connections

of your loudspeakers and cables depending on the EUROPOWER speaker output

you choose.

EUROPOWER PMP518M

output

OUtPUt

For unbalanced use, pin 1 and pin 3 have to be bridged

MAIN MONO

POS

NEG

POS

NEG

Fig. 4.3: XLR connectors

Tab. 4.1: Pin connections of the professional loudspeaker connector

behringer.com

EUROPOWER PMP518M User Manual

5. Applications

This illustration shows just one example of how the channels of your power mixer The following illustration shows a live application with the PMP518M as monitor

can be used, including the connection of mono and stereo sources, and the tape

ins and outs recording the mix signal or playing back external signals.

mixer and a BEHRINGER EURODESK SL2442FX-PRO that provides the FOH main

mix signal. The PMP518M receives the Aux Send signal of the EURODESK that is

used for the monitor mix on stage.

EUROLIVE

E1520A

EUROLIVE

E1520A

FOH Mix

EUROPOWER

EP2000

Tape

In/Out

DAT Recorder

Vocal mic

ULTRA-G

GI100

Keyboard

EURODESK

SL2442FX-PRO

Aux

Send

Electric Bass

V-AMP 2

Electric Guitar

EUROPOWER PMP518M

Fig. 5.1: Standard set-up

Monitor Mix

Fig. 5.2: Setup with PMP518M as monitor mixer

behringer.com

10 EUROPOWER PMP518M User Manual

6. Speciﬁcations

Microphone Inputs

DSP

Type

XLR, electronically balanced

Converter

24-bit Sigma-Delta,

40 kHz

Mic E.I.N. (20 Hz - 20 kHz)

@ 0 Ω source resistance

@ 50 Ω source resistance

@ 150 Ω source resistance

Frequency response

Sampling rate

-122 dB / -125 dB A-weighted

-121 dB / -124 dB A-weighted

Display

Type

2-digit, 7-segment LED

Ampliﬁer

< 10 Hz - 100 kHz (-1 dB),

< 10 Hz - 200 kHz (-3 dB)

Output power

(RMS @ 1 % THD (sine wave))

62 W (8 Ω), 105 W (4 Ω)

100 W (8 Ω), 180 W (4 Ω)

Gain

+33 dB, +8 dB with pad

+12 dBu @ 10 dB gain

Output power

(Peak Power)

Max. input level

Impedance

approx. 2.2 kΩ balanced,

1.1 kΩ unbalanced

Power Supply

Signal-to-noise ratio

Distortion (THD+N)

110 dB/114 dB A-weighted

(-11 dBu in @ +33 dB gain)

Mains voltages

U.S./Canada

120 V~, 60 Hz

0.001% / 0.0008% A-weighted

China/Korea

220 V~, 50/60 Hz

230 V~, 50 Hz

Mono Line Inputs

Type

Europe/U.K./Australia

Japan

1" TRS connector, balanced

100 V~, 50 - 60 Hz

120/230 V~, 50 - 60 Hz

max. 290 W

Impedance

approx. 80 kΩ balanced,

40 kΩ unbalanced

General export model

Power consumption

Fuse

Max. input level

+30 dBu

100 - 120 V~: T 6.3 A H 250 V

220 - 240 V~: T 3.15 A H 250 V

Mains connection

Standard IEC receptacle

Low

High

80 Hz / 15 dB

12 kHz / 15 dB

Physical / Weight

Dimensions (H x W x D)

approx. 4 3/5x 18 1x 8 7/8"

approx.117 x 470 x 225 mm

Main Mix System Data

Noise

Weight (net)

approx. 15.88 lbs / 7.2 kg

Main mix @ -∞,

Channel fader -∞

-106 dB / -110 dB A-weighted

-87 dB / -90 dB A-weighted

-80 dB / -82 dB A-weighted

Main mix @ 0 dB,

Channel fader -oo

Main Mix @ 0 dB,

Channel fader @ 0 dB

Loudspeaker Outputs

Type

Neutrik Speakon-compatible,

1" TS connectors

Load impedance

4-16 Ω

behringer.com

11 EUROPOWER PMP518M User Manual

FEDERAL COMMUNICATIONS

COMMISSION COMPLIANCE

INFORMATION

EUROPOWER PMP518M

Responsible party name:

Address:

MUSIC Group Services USA, Inc.

18912 North Creek Parkway,

Suite 200 Bothell, WA 98011,

USA

Phone/Fax No.:

Phone: +1 425 672 0816

Fax: +1 425 673 7647

EUROPOWER PMP518M

complies with the FCC rules as mentioned in the following paragraph:

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined

by turning the equipment oﬀ and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

•

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit diﬀerent from that to which the

receiver is connected.

•

Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC rules. Operation is subject to the

following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may

cause undesired operation.

Important information:

Changes or modiﬁcations to the equipment not expressly approved by MUSIC Group

can void the user’s authority to use the equipment.

behringer.com

321 Studios Chipper Plesk 7x Reloaded User Manual
ACDelco Automobile Parts 26 SI User Manual
Acer Laptop 2350 User Manual
AEG Washer 76730 User Manual
Alcatel Carrier Internetworking Solutions Switch 6624 User Manual
Allied Telesis Network Cables AT MC606 User Manual
American DJ DJ Equipment Flight Moon User Manual
ATI Technologies Computer Hardware X1950 PRO User Manual
Bakers Pride Oven Kitchen Entertainment Center PHC70 MPINS User Manual
Barco Air Conditioner 08 0311105 00 User Manual