Related Documents
To install the AT-WDRPS-10, perform the following procedure:
way to access the most recent documentation, software, and technical information
for all of our products. For details on the features and functions of your Allied
Telesyn AT-WD1008 chassis and modules, refer to the following manuals from our
web site:
Note
The AT-WDRPS-10 unit can be installed while the multiplexer is powered ON.
You do not need to power OFF the multiplexer to install the RPS.
❑ AT-WD1008 Gigabit Ethernet Wavelength Division Multiplexer
1. Loosen the two thumbscrews that secure the blank faceplate over the right-
hand redundant power supply expansion slot located on the front panel of the
AT-WD1008 Multiplexer and remove the cover.
Installation Guide
PN 613-50367-00
❑ AT-S47 Management Software User’s Guide
S
T
TX
PN 613-50371-00
TX
L
N
K
T
S
T
X
X
RX
AT-WDRPS-10
Redundant Power Supply (AC)
L
N
K
T
S
T
T
TX
WEST
RX
T
R
X
X
EAST
R
RX
TX
RX
L
N
K
T
S
T
TX
E
A
N
S
T
O
R
M
A
L
C
H
5
RX
TX
TX
Package Contents
C
H
6
RX
TX
RX
RX
TX
Installation Guide
C
H
7
TX
RX
Make sure the following items are included in the shipping package. If any item is
missing or damaged, contact your Allied Telesyn sales representative for
assistance.
F
AN
A
B
P
O
S
W
E
N
M
R
B
S
P
U
M
P
O
P
D
U
L
Y
L
E
C
H
8
F
AN
❑ One AT-WDRPS-10 Redundant Power Supply (AC) Module
❑ One AC Power Cord
Allied Telesyn, Inc.
960 Stewart Drive, Suite B
Sunnyvale, CA 94085 USA
❑ This installation guide
Tel 1 (408) 730-0950 • Fax 1 (408) 736-0100
❑ Warranty card
2. Remove the AT-WDRPS-10 unit from its shipping package.
3. Slide the AT-WDRPS-10 unit into the RPS expansion slot.
Installing the AT-WDRPS-10 Power Supply
T
X
TX
RX
L
N
K
T
S
T
X
X
R
X
T
L
N
Caution
K
T
S
T
T
X
X
X
W
E
T
S
R
T
E
A
S
R
T
R
X
TX
RX
L
N
K
T
S
T
T
X
EAST
TX
N
O
R
M
A
L
Before installing the module, refer to the AT-WD1008 Installation Guide for
electrical safety and emission information.
CH
5
R
X
T
X
CH
6
R
X
TX
RX
RX
T
X
Overview
CH
7
TX
RX
F
AN
A
B
POWER
SNMP
SUPPL
MODULE
Y
B
CH
8
The AT-WDRPS-10 is an AC Redundant Power Supply (RPS) for the AT-WD1008
Multiplexer chassis. When installed, the unit shares the load of powering the
chassis with the standard power supply that comes pre-installed in the chassis. If a
power supply fails, the remaining unit provides all power to the system, thereby
preventing a network failure. The power supply is hot-swappable, meaning that
you can install it while the chassis is powered ON.
F
AN
Caution
Do not install the AT-WDRPS-10 module in an AT-WD1008 chassis designed
for DC power. An AC powered chassis has two AC power sockets on the back
panel.
P
O
W
E
R
F
A
U
L
T
P
O
W
E
R
F
A
U
L
T
PN 613-50369-00 Rev A
1
2
3
|